gearbox
- Thread starter digbymole
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 83,310
- Location
- Embasinga stocæ
try putting it into difflock and see if yu get drive .
- Posts
- 4,201
- Location
- North Norfolk
did you try what madhatman said? if so did you get drive?
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
you need to see if one prop is turning while in gear .,can you change through the gears without pressing clutch
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
if you can change gear without feeling box turning then clutch plate is most likely
can anyone help
i have stripped landy gear box and checked splines but they are ok also all gears work as in there is no damage in t/box everything moves freely
and it turns when landy on tick over in neutral as it should so that would say to me the lay shaft is ok !!!
i put into gear and release clutch nothing happens only a wearing /grinding
that goes if i depress clutch ? so this would say clutch working ok ? fluids ok and theres pressure at the pipe when pressure applied ?(it moves )
i have tried all hi/lo in all positions no joy even disconnected and done it by hand ?
as anyone got any ideas before i rip it out ?
clutch may have gone and still working to some extent ?
also it was running fine untill i had the handbrake/cable done and its only done 10 mile since before it went ! maybe fluke or may have something to do with it
thanks ian :rolly:
i have stripped landy gear box and checked splines but they are ok also all gears work as in there is no damage in t/box everything moves freely
and it turns when landy on tick over in neutral as it should so that would say to me the lay shaft is ok !!!
i put into gear and release clutch nothing happens only a wearing /grinding
that goes if i depress clutch ? so this would say clutch working ok ? fluids ok and theres pressure at the pipe when pressure applied ?(it moves )
i have tried all hi/lo in all positions no joy even disconnected and done it by hand ?
as anyone got any ideas before i rip it out ?
clutch may have gone and still working to some extent ?
also it was running fine untill i had the handbrake/cable done and its only done 10 mile since before it went ! maybe fluke or may have something to do with it
thanks ian :rolly:
Last edited:
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
clutch center broken away from plate can look okay till you really look ,to check for l/s you try in 4th
yes mate i think you are on the same lines just a pity theres no access hole to check fully !! what am i looking for when i try in 4th just a more fearse rumble mate ?
thanks james (looks like im getting dirty)
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
4th gear works if l/s shaft bust ,can you change gear with engine running not using clutch
yes mate
i have checked everything and all working as should do ? however still no drive ?
i have had inspection covers off t/box and all seems to move and spline is driving cogs
props not free turning suggesting the no shafts broken so seems not the t/box
all gears select easy and as the should so gear box seems fine
all i can think of is the clutch center as gone ? it seems ok but i cant see in bell housing
to see so im just assuming ?
anybody any wiser than me or had the same problem that could help me before i rip the lot out ( ball ache )
thank Ian
i have had inspection covers off t/box and all seems to move and spline is driving cogs
props not free turning suggesting the no shafts broken so seems not the t/box
all gears select easy and as the should so gear box seems fine
all i can think of is the clutch center as gone ? it seems ok but i cant see in bell housing
to see so im just assuming ?
anybody any wiser than me or had the same problem that could help me before i rip the lot out ( ball ache )
thank Ian
one or other mate (outward splines are rotating the cogs so must be a gearbox out job thanks
