Fuel Filler Problem

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
L

Leaky Landy

New Member
Posts
58
Ive trawlled the forum but cant find anything on this subject, can anyone help. My Mrs has a TD4, on a 52 plate, fine perfect car, just one anoying problem. Putting Diesel in it is and absolute Bitch of a job. Weve tryed all sorts of filling stations, positions for the fill nozzle but it still refuses to take on diesel at anything more than a trickle rate or the nozzles cut out. Its at the point where the pumps sometimes time out before weve managed to get 20quids worth in. A fill up is really an ordeal. Our mechanic has had a look at it and drawn a blank, has anyone else come across this and how did you deal with it?
Answers on a postcard to.........
 
Leaky Landy said:
Ive trawlled the forum but cant find anything on this subject, can anyone help. My Mrs has a TD4, on a 52 plate, fine perfect car, just one anoying problem. Putting Diesel in it is and absolute Bitch of a job. Weve tryed all sorts of filling stations, positions for the fill nozzle but it still refuses to take on diesel at anything more than a trickle rate or the nozzles cut out. Its at the point where the pumps sometimes time out before weve managed to get 20quids worth in. A fill up is really an ordeal. Our mechanic has had a look at it and drawn a blank, has anyone else come across this and how did you deal with it?
Answers on a postcard to.........
Click to expand...
had freelanders since they were born and never had that problem
 
I have experienced it a few times - not sure if it's the pumps/nozzles of a particular station as I fill up at lots of places. When it does happen though I find that pulling the nozzle out a bit (half in half out) seems to work.

Interestingly I filled up with some B30 from a Morrisons recently - took about 10 mins to fill up - not sure if pump was busted or what, but was filling at a very very slow rate!
 
I had the same problem.
I find that turning the nozzle through 90 degrees so that the grip is pointing rearwards (as is the nozzle in the pipe) solves the problem. The vent from the tank comes up to the front of the filler pipe. Air rising through this hits the incomong fuel which is blown back triggering the cut-off.
By efffectively pointing the nozzle down the rear of the pipe the fuel does not flow over the vent opening (and for me at least) the car fills OK.
 
Leaky Landy said:
Thanks for all the usefull answers!:cool:
Click to expand...
Ther is a flap at the end of the inlet hose [fuel shut orft incase its rolled in a accident] iwould suggest that this is stuck half way causing a restriction in fuel flow. . . .ram a bit of plastic pipe down it [take it out after]. . .then try agin:) :) :)
 
I find leaving the nozzle about 2 inches out does the trick. Had a number of Freelanders at work, and they were all the same.
 
Thanks for this lads, I think Ive probably tried every filler position apart from the one you suggest. We'll have a go and let you know, if it dont work we'll try the ram a bit of plastic pipe routine! Thanks again.
 
You must log in or register to reply here.

Similar threads

D
Indicator problem
Replies
9
Views
1K
dannyboy8
D
Ian M in France
Another td4 starting problem
Replies
14
Views
1K
Ian M in France
Ian M in France
Brown
TD5 electronic faults - any ideas?
Replies
15
Views
993
Brown
Brown
D
FL2 Haldex strip down
2 3
Replies
41
Views
4K
Arctic2
Arctic2
A
Freelander hse 2.2 td4 auto gearbox problem
Replies
2
Views
1K
a11an#1
A
Back
Top