Rsturbo
Member
- Posts
- 45
- Location
- Kidderminster
Hi guys so I've almost got the disco back up and running after a long time. I've come across this pipe which would explain the coolant leak I had before but couldn't find. Where does it go too??
Expansion tank pipes
- Thread starter Rsturbo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Hi guys so I've almost got the disco back up and running after a long time. I've come across this pipe which would explain the coolant leak I had before but couldn't find. Where does it go too??
Rsturbo
Member
- Posts
- 45
- Location
- Kidderminster
Thank you mate.
jamesDiscoTD5
Active Member
- Posts
- 94
- Location
- West Midlands
The pipe in your hand is the one that's supposed to go the radiator. The other pipe is the one that's supposed to point down.
I'm not sure if them being the wrong way around makes any difference though.
I'm not sure if them being the wrong way around makes any difference though.
sierrafery
Well-Known Member
- Posts
- 17,905
- Location
- Arad/Romania
+1 for that^^^^ with the addendum that it's not OK to be the wrong way around as the return hose which comes from tha radiator goes below the cap's o-ring to be flow all the time while the overflow pipe(nr 2) goes from above the seal as it's supposed to let air or coolant out when the pressure exceeds 1'4 bar to open the cap's valve if you see what i mean
so mr @Rsturbo swap those pipes ASAP
discool
Well-Known Member
- Posts
- 13,620
Seems a bit involved 
Last edited:
Rsturbo
Member
- Posts
- 45
- Location
- Kidderminster
I've just seen this. Does that explain why when I've just started it now why it's leaking out of the cap??
Rsturbo
Member
- Posts
- 45
- Location
- Kidderminster
jamesDiscoTD5
Active Member
- Posts
- 94
- Location
- West Midlands
Undo that jubilee clip and put the pipe going to the radiator onto the other pipe.
Rsturbo
Member
- Posts
- 45
- Location
- Kidderminster
Rsturbo
Member
- Posts
- 45
- Location
- Kidderminster
Thank guys I wouldn't of known that. And I was going to buy a new cap.
sierrafery
Well-Known Member
- Posts
- 17,905
- Location
- Arad/Romania
Yes it does cos the return flow goes above the seal not below it back into the tank
Rsturbo
Member
- Posts
- 45
- Location
- Kidderminster
So I've done that thanks. So I do have a problem with the heating. That there is none. I've changed the water pump (pig of a job) and changed the thermostat still blowing cold and it's been running for 40 mins
Attachments
sierrafery
Well-Known Member
- Posts
- 17,905
- Location
- Arad/Romania
To blow warm the coolant must be hot as well and as the gauge on your's is below the middle the coolant is not warm enough, the needle should go to the middle at 70*C while the heater core can be clogged as well... if it ran for 40 minutes at idle that means nothing if it's cold outside, a Td5 at idle would never get hot enough... though try to stop the viscous fan with a rolled up newspaper after a cold start and if you can't that's another reason for hard warming up.
Rsturbo
Member
- Posts
- 45
- Location
- Kidderminster
The temp has never reached half way since we've had it. Il try to stop the viscous fan some how.
sierrafery
Well-Known Member
- Posts
- 17,905
- Location
- Arad/Romania
So you didnt drive it hard since then? .... then don't expect the the heater to blow warm unless the temp sensor is fubar
If you can't stop the fan with cold engine means that it's locked solid so you need a new one which is freewheeling and locks only when the radiator is hot
Rsturbo
Member
- Posts
- 45
- Location
- Kidderminster
No it's been of the road for a bit. So took the opportunity to change a few things i.e water pump and thermostat hoping that would sort the issue out. I will try that with the viscous fan and report back tomorrow at some point
- Posts
- 45,046
- Location
- East Dorset
+1^
