biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
Dartford rebore
L322 does any one have
- Thread starter biketeacherdave
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
holidaychicken
Well-Known Member
- Posts
- 4,014
- Location
- Kent
Nice one, not far from me, were they skimmed ?
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
Yep skimmed, proper good job done on them
holidaychicken
Well-Known Member
- Posts
- 4,014
- Location
- Kent
Great, i'll keep them in mind, i may have a project coming...............
Thank you
Thank you
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
Will be posting a full write up on this if it all works
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
So after the rebuild and fitting the engine back in it was time to turn it over to get the oil pressure up before connecting the coil packs and fuel system.
Datatek
Well-Known Member
- Posts
- 43,928
- Location
- Near Poitiers SW France
Looke as though you have put it in the wrong way up, this may cause you problems
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
Yep all the fluids drained outLooke as though you have put it in the wrong way up, this may cause you problems
holidaychicken
Well-Known Member
- Posts
- 4,014
- Location
- Kent
Did you take the engine out forwards minus the transmission ?
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
Yep out from the front with the TQ attached
holidaychicken
Well-Known Member
- Posts
- 4,014
- Location
- Kent
Looks nice and easy, if I finish my build I’ll swap mine out like that, is yours all running now and did you rebuild your vanos ?
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
This has been a total rebuild of the heads, vanos, new sh bottom end due to scoring of cylinder 3 I think. Found x3 coil packs down back on it Wednesday. Full write up with pics to follow
holidaychicken
Well-Known Member
- Posts
- 4,014
- Location
- Kent
Where is the old bottom end ?
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
Under a tarp on the driveway next to the car.
- Posts
- 16,475
I think Andy is angling for something!?!?!
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
Well were all debating who gets it to turn into a coffee table so I think he is out of luck lol
holidaychicken
Well-Known Member
- Posts
- 4,014
- Location
- Kent
i might be able to turn it into an engine again, and then a coffee table
Come on, I need the practice
Come on, I need the practice
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
Well we got this running at last one of the cams was 180 degrees out. Doh
holidaychicken
Well-Known Member
- Posts
- 4,014
- Location
- Kent
Easy to get right and wrong !
biketeacherdave
Well-Known Member
- Posts
- 4,653
- Location
- south east london
No it was a silly error as the cams are marked at the rear. E for inlet and A for exhaust and should be clearly seen when at tbc on both banks.
We found this out afterwards, engine fires and runs sweet as now just have to sort a vanos rattle and put the rest of it back together
We found this out afterwards, engine fires and runs sweet as now just have to sort a vanos rattle and put the rest of it back together
Similar threads
