Disco 2 Hub reassembly question.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
A

adam koronka

Member
Posts
52
Location
UK Somerset
Hi good folks. Just reassembling after changing upper and lower front ball joints. Torqued the collet up to 5 its and the top and bottom nuts of the hub/knuckle you can see in the photo up to 55. My question is that the hub is very stiff to turn when I grip it with both hands. Is this normal and is only happening because the balljoints are new, or have I done something wrong, or is there an adjustment to be made. Just want to make sure before I spanner her up.

Many thanks

Adam
 

Attachments

  • hub.jpeg
    hub.jpeg
    225.9 KB · Views: 216
Hi, well I tried a different hub carrier/knuckle/collet, torqued it up and it was the same. I then connected up the steering, started the engine and the steering feels absolutely fine, with no binding or variation through the lock, so I suppose it's just new?

A
 
Don't know if you have RAVE but it says to first fit the upper ball joint nut and tighten to 110Nm. The lower one should then go in and torqued to 135Nm. I believe if this procedure is not followed, the lower ball joint will be taking more tension than it should.
 
NPG said:
Don't know if you have RAVE but it says to first fit the upper ball joint nut and tighten to 110Nm. The lower one should then go in and torqued to 135Nm. I believe if this procedure is not followed, the lower ball joint will be taking more tension than it should.
Click to expand...

Hi, I missed this and it makes perfect sense, thanks for pointing it out

Cheers

Adam
 
NPG said:
Don't know if you have RAVE but it says to first fit the upper ball joint nut and tighten to 110Nm. The lower one should then go in and torqued to 135Nm. I believe if this procedure is not followed, the lower ball joint will be taking more tension than it should.
Click to expand...
I done my joints at least 3yrs ago and didn’t do this. Only because I had no clue I needed to. Didn’t torque them either as I rarely torque anything. It’s been fine, but I suppose time will tell with these things. After reading this, I would torque them if I was doing them again as I can see the sense in it.
 
meego said:
I done my joints at least 3yrs ago and didn’t do this. Only because I had no clue I needed to. Didn’t torque them either as I rarely torque anything. It’s been fine, but I suppose time will tell with these things. After reading this, I would torque them if I was doing them again as I can see the sense in it.
Click to expand...
it doesnt really matter joint will fit in the taper as far as it will then threads stretch if you tighten the nuts tight holding the joint tight ,unless you leave nut loose or are about to strip the threads
 
jamesmartin said:
it doesnt really matter joint will fit in the taper as far as it will then threads stretch if you tighten the nuts tight holding the joint tight ,unless you leave nut loose or are about to strip the threads
Click to expand...
I’m no mechanic, but i think I’ve got quite a good feel for tightening things up. It’s not failed me yet. Cheers
 
You must log in or register to reply here.

Similar threads

mad85
Disco 2 Front hub/axle seal leaking
Replies
19
Views
2K
mad85
mad85
L
Disco 2 brake question
Replies
5
Views
707
landynutterme
L
A
Freelander 2: does the Freelander 2 have a removable reluctor ring?
Replies
3
Views
2K
AntMan1
A
L
Hand brake question
Replies
14
Views
1K
romanrob
R
J
Discovery 2 PAS Problem (SOLVED)
Replies
11
Views
2K
JakeFrost
J
Back
Top