Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
is it like a buzzing if so top of pump lack of fuel
Diesel Just won't start
- Thread starter HandyPaul
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 58,170
- Location
- Preston Lancs.
Nozzle shaped lamp is the Mil check lamp on the diesel, believe an engine shaped lamp was used on later cars though. Could be advance solenoid modulating could be Elab (shut off valve) dropping in and out. You really do need diagnostics on this.
Last edited:
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
When I do a filter change I don't bother to prime it i just turn it over for a bit Consecutively after I stop and before its running the top of the pump is buzzing after each small turnover if you turn ignition on and off it goes this happens untill fuel is has filled the injector pump .
- Posts
- 58,170
- Location
- Preston Lancs.
When you remove the filter you don't drain the pump. You should always fill the new filter with fuel, what is the point in introducing air to the system? Noise will be quantity servo buzzing and yes lack of fuel in pump top will cause it to be more audible. So you don't fill filter, don't prime system and pump fuel through by cranking. That cannot be done on many P38 diesels so a bit of bad advice really.
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
Wasn't advice just what I do and the Consequences yes there is fuel in the pump but once I start cranking I guess it emptys faster than the filter fills
Last edited:
- Posts
- 58,170
- Location
- Preston Lancs.
Want advice just what I do and the Consequences yes there is fuel in the pump but once I start cranking I guess it emptys faster than the filter fills
Yeah but it's not about your car it's about someone following your advice and trying that with a pre 99 car and flattening his battery trying to get fuel through. Because his car does not run the fuel pump whilst being cranked.
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
This tread isn't about changing a filter is it
The op said there was a buzzing I'm giving him an indication as to why , most don't even know what a
Elab shut of valve is
- Posts
- 58,170
- Location
- Preston Lancs.
This tread isn't about changing a filter is it
The op said there was a buzzing I'm giving him an indication as to why , most don't even know what a
Elab shut of valve is
Elektrisches Abstellventil. Wonder if he has had the banjo slack and checked for fuel flow there?
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
I'm sure the smell of diesel And the wet patch followed by a pool of diesel would of indicated that .i think this bypass don't help one bit either plus no diesel heater it all a bit of a bodge really
Last edited:
- Posts
- 16,482
The flow from the In Tank Pump should be 180ml in 10 seconds (IIRC - ask the Wammer)
Datatek
Well-Known Member
- Posts
- 45,801
- Location
- Near Poitiers SW France
Correct, but if the system is full, most will start even with a duff pump.
Where exactly is the buzzing coming from? Left or right of engine bay when you stand in front looking at it?
I'm wondering about the fuse box, many problems originate there, bad connections/duff relay causing shut of valve to buzz but not open for example.
As long as your bypass is airtight it will cause no problem. The fuel heater probably doesn't even come on unless the air temp is below zero and many cars do not have them.
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
That's unless he's tank is full of crud and causes a blockage in the fip, I always wonderd what a fuel filter was for
Datatek
Well-Known Member
- Posts
- 45,801
- Location
- Near Poitiers SW France
We are talking about test conditions trying to get it to start, not about running the thing. Since it won't start it is not going to pull **** from the tank is it?That's unless he's tank is full of crud and causes a blockage in the fip, I always wonderd what a fuel filter was for
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
The op has said there is no fuel comming out of the fip you don't know how long this bodge has been in place is not a test it just conked out wont start no fuel comming out of the fip who says its not blocked
Datatek
Well-Known Member
- Posts
- 45,801
- Location
- Near Poitiers SW France
Post #1 he say's he has fuel coming out of the banjo at the FIPThe op has said there is no fuel comming out of the fip you don't know how long this bodge has been in place is not a test it just conked out wont start no fuel comming out of the fip who says its not blocked
It just does not get to the injectors. Loss of sync.
JohnnyCrash
New Member
- Posts
- 1,917
Post #1 he say's he has fuel coming out of the banjo at the FIP
It just does not get to the injectors. Loss of sync.
or been playing with FIP and didn't mark off where the middle plate should be
- Posts
- 58,170
- Location
- Preston Lancs.
or been playing with FIP and didn't mark off where the middle plate should be
Possible but he does not say. If pump top is in wrong place holding control collar open it will never start.
JohnnyCrash
New Member
- Posts
- 1,917
+1 found out the hard way haha
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
What are you on about the banjo is the pipe that bolts onto the fip he has fuel to the fip but not after he has now said there is a buzzing if it was out of sync there would be no power to it and it would not buzz would it as I said now the fuel is not passing through a filter it could have a block in the fip read again!Post #1 he say's he has fuel coming out of the banjo at the FIP
It just does not get to the injectors. Loss of sync.
Similar threads
