Bell housing prob for disco 200tdi into 90

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
P

PhilB

New Member
Posts
46
Right so I've checked through all the threads on disco 200tdi into defender. So it's all done apart from we've used the original disco flywheel cover. So now the 4 sandwich bolts across the bottom don't line up. Now should I drill new holes in the bell housing or swap the flywheel covers. Reason I
asking as my dad is hard to argue with and thinks the 4 bolts are there for a reason. Any help? Oh and it's a lt77 box
 
Beast o Bodmin said:
a disco box will not fit defender you need to change input shaft and bell house or get a defender box to fit.

i have a spare here for sale 300 quids plus post or collect.
Click to expand...
he's puttin a disco engine on a 90 box, cock

either drill and tap as necessary or use the flywheel cover off original engine
 
Thankyou gratch!! Read the post guys. I'm using the lt77 gearbox with a 200tdi engine. I already drilled the small holes for the dowls but missed the bolts across the bottom. Hohum take the bell housing off again tomorrow a d drill some more. Cheers
 
Beast o Bodmin said:
disco 200 and 90 box.nice that will do about 20mph.
Click to expand...


Fook off ya fick cuunt. I dun't mind peeps taking the **** if they're doing it to annoy someone specifically or just for a general laff. But when every post is inane drivel and aimed at noone or everyone, it just gets boring.

Have a laff and a windup by all means. But for ****sake try and keep it intelligent.
 
I just tapped the blind holes in the disco lump and stuck a couple of bolts in them. I ran my conversion without the bolts for over a year on and off road with no problems.
 
The Mad Hat Man said:
scooz me - where does he say a defender box - sure he says LT77, but it could be either a defender or disco box! - or have i missed summat?
Click to expand...

PhilB said:
Right so I've checked through all the threads on disco 200tdi into defender. So it's all done apart from we've used the original disco flywheel cover. So now the 4 sandwich bolts across the bottom don't line up. Now should I drill new holes in the bell housing or swap the flywheel covers. Reason I
asking as my dad is hard to argue with and thinks the 4 bolts are there for a reason. Any help? Oh and it's a lt77 box
Click to expand...
as highlighted, plus why would he need todrill disco bellhousing to disco engine?;)
 
k - so its deffo a defender box, but back to my first point - int the disco bellhousing longer/deeper, coz i thought the disco box had a longer input shaft??
 
so - to answer his Q - dont use the disco bellhousing - use the defender bellhousing, but tap the blank holes in the injun, so yu can bolt it up proper.
 
You must log in or register to reply here.

Similar threads

P
Classic VM 2.5 to 200tdi swap - LT77 bell housing
Replies
10
Views
2K
Rangieman123
Rangieman123
M
Discovery1 lt230 in place of LT230R from a 12D?
Replies
3
Views
873
MrF
M
xDParis64
Freelander 1 Converting from wasted spark to distributor (or Visa Versa)
Replies
0
Views
450
xDParis64
xDParis64
L
200tdi 300tdi combi engine?
Replies
1
Views
1K
ifloochies
ifloochies
Blob
L322 Solved - C1A13-64 (AF) Pressure does not decrease when venting gallery
Replies
2
Views
3K
stuu
stuu
Back
Top