Are these MOT failures?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.

payydg

Well-Known Member
Posts
3,907
Location
Aberdeenshire
So I normally take HMS landy to an old family friend for an MOT. Let’s just say he overlooks minor issues that have been present since I’ve had it. Due to Covid probably going to have to take it to someone local.

These are the following issues I’ve never been able to solve/have ignored.

No rear windscreen wiper - not been present for almost 10yrs.

Brake lines cable tied on the rear axle. The metal clips have rusted to **** unsurprisingly.

Weird earth issue when I put the head lights on full beam one turns off.

likely MOT failures?
 
Could be just a dead full beam element in the bulb, unlike many modern vehicles where the dip stays on when you switch to main on old landys the dip goes out when you switch to main. Result no light that side.
I had an interesting one the other night. Cruising along an unlit wooded road, bunged the hibeams on, no lights at all! Very quickly switched back to dipped. Tried it again (why!!??), and full beans worked fine. Only did it once.
It did remind me I needed to make a sacrifice to Lucas, God of Darkness.
 
So I normally take HMS landy to an old family friend for an MOT. Let’s just say he overlooks minor issues that have been present since I’ve had it. Due to Covid probably going to have to take it to someone local.

These are the following issues I’ve never been able to solve/have ignored.

No rear windscreen wiper - not been present for almost 10yrs.

Brake lines cable tied on the rear axle. The metal clips have rusted to **** unsurprisingly.

Weird earth issue when I put the head lights on full beam one turns off.

likely MOT failures?
Cable ties, no problem.
Rear wiper, if you can get it going is probably the best. If not, remove it completely.
Headlights will need to be working properly, unless the tester is very negligent.
 
What I did with my brake line was put abit of rubber tubing over the top first before cable tieing.

I don't think I'd want my brake line rubbing on steel
That is a good plan. Clear plastic tubing, or the foam tubes that they use for the edges of fridge shelves in transit also work well.
But in practice, provided the brake pipe is held tightly and flat against the axle or chassis, there is never a problem.
 
That is a good plan. Clear plastic tubing, or the foam tubes that they use for the edges of fridge shelves in transit also work well.
But in practice, provided the brake pipe is held tightly and flat against the axle or chassis, there is never a problem.

One of the brake pipes on the jag I'm rebuilding looked really good, until I removed it and where it had slightly been rubbing on the inner wheel arch after someone had done some welding , it was like tin foil , scary :eek:
 
One of the brake pipes on the jag I'm rebuilding looked really good, until I removed it and where it had slightly been rubbing on the inner wheel arch after someone had done some welding , it was like tin foil , scary :eek:
If it was moving, it wasn't held tightly. Where the brake pipes run across panels, you can get little clips, that poke into a drilled hole, and the brake pipe snaps into them. But along an axle, as with the rear pipe joining the rear brakes on a Defender, cable ties are fine.
 
Iirc the pipes were tied to the rear axles from new? some had metal clips and others large ties that the pipes attached to.

As for cable tying, it has to be tight, anyhting less than tight means all them pipes/cables are now held loosely to each other, and are going ti have a serious rubbing each other off party until one of them blows!
Scania trucks are famous for this, the trucks blow themselves off as do the drivers dreaming of their trucks.
 
Look out! Broke and kurt will be eating Yorkie bars now :rolleyes:


I love to slag them off to wind people up, and i used to hate the scanias with a passion and actually took my current job as there were no scanias, then 1 year later 30 scanias turned up! but 5 years on the euro6 dafs have been a total let down, parts spend and reliablilty is horrific, yet the scanias have been good, far from perfect but way way more reliable than the euro6 dafs.
I am told the current generation dafs are meant to be very good.
 
Back
Top