bankz5152
Well-Known Member
- Posts
- 9,139
- Location
- South London/North Kent
i know what must i have been thinking 
TD5 90 Project
- Thread starter KISSMYAURA
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
i know what must i have been thinking 
raywin
Well-Known Member
- Posts
- 3,808
- Location
- North Yorkshire
Just out of interest can you tell me where you bought the insulation? I want to put some more in my 90.
Its on ebay mate. Silent coat is also good and on there. I used 'the sound deadening shop' via their actual website rather than their ebay shop.
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
So rear axle rebuild then.........and why not!
- Stub Axles
- Wheel Bearings / Seals
- Brake Mud Shields
- Brake Lines to Cupro
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
Happy with the colour match.....if i polish the rest of the truck o course
Shut lines fine, its a truck, so very happy On to door number two now.
PS anyone want to buy some TD5 doors if you can weld and replace bottom box section they all good?
Shut lines fine, its a truck, so very happy On to door number two now.
PS anyone want to buy some TD5 doors if you can weld and replace bottom box section they all good?
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
.
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
Rear hub rebuild prep, new brake shields arrived so flicked on the first coat of stone chip.
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
Decided to use Lock button push as location for my alarm / immobiliser tell tail.
Swapped LED for smaller R/B bi-colour one.
Swapped LED for smaller R/B bi-colour one.
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
Made up a set of CTEK charging / battery conditioning leads with my hydro-crimper, and heat shrink sleeves.
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
The man from del-monte says time to get a new battery son.......
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
Last edited:
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
New bearings, Stub Axle, drive shafts, flanges, mud shields etc. Had to drill a stub axle bolt out, thats 2 hours of my life I wont get back, FFS.
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
New Front (EBC GRN) and Rear (BREMBO) brake pads.
Next up is renewing the brake lines, will be making them up myself in cupro.
Rears with a stainless braided coupler.
Next up is renewing the brake lines, will be making them up myself in cupro.
Rears with a stainless braided coupler.
bankz5152
Well-Known Member
- Posts
- 9,139
- Location
- South London/North Kent
Like it
All that extra breaking guna need some extra power
All that extra breaking guna need some extra power
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
Like it
All that extra breaking guna need some extra power
need to do that bloody A Frame first!
bankz5152
Well-Known Member
- Posts
- 9,139
- Location
- South London/North Kent
Buy a new fulcrum save a headache!
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
bankz5152
Well-Known Member
- Posts
- 9,139
- Location
- South London/North Kent
Niiiice! Proper job!!!
WillMealor
New Member
- Posts
- 3
- Location
- Wirral
Lovely build
KISSMYAURA
Well-Known Member
- Posts
- 2,612
- Location
- KENT
cheersbuddy! Remind me, @bankz5152 what front light guards did you go for in the end?
