What have you done to your Landie today.

[a2dds]

painted the rear crossmember with some hammered hammeriate black

 

[DJ Xan]

Stripped out the heater box someone's been putting cement in the matrix :lol:
Now in a bucket soaking for its hose out tomorrow.
Might get some heat out of it

 

[ratty]

I emptied the last of the coal out of the back of mine.

 

[drewster]

I emptied the last of the coal out of the back of mine.

I thought something was odd with your car now I know its a steam engine

 

[ratty]

I thought something was odd with your car now I know its a steam engine

I've been rumbled.

 

[Dr No]

Gratuitous pic -

Gratuitous or not very nice.

 

[big si]

Pulled lump out ready for crank seal, got interior light and dash lights working, heater working, reverse light working, fitted thermal fan and switch , stereo fitted, got cb working,wipers working. Got to fit crank seal and refit engine then do head gasket and refit dash and she's ready for the chippy run. I'm fookin knackered

 

[Freelaner]

Pulled lump out ready for crank seal, got interior light and dash lights working, heater working, reverse light working, fitted thermal fan and switch , stereo fitted, got cb working,wipers working. Got to fit crank seal and refit engine then do head gasket and refit dash and she's ready for the chippy run. I'm fookin knackered

yer did all that at work

 

[big si]

Yep with a hand from my bro'. Him being a sparky helps.

 

[landowner]

Drove it carefully as the swivel bearings are very loose.

Got the parts at 17.10 this evening so too late to start but tomorrow i'll be having a go at fitting swivel repair kit and new disc, pads, brake pipe and braided hose to near side front of Disco and just repair kit and braided hose to offside as that has new disc and pads on it already

Got inner hub seals for rear as well but think thats goin to be done Friday.

 

[Dr No]

Drove it carefully as the swivel bearings are very loose.

Got the parts at 17.10 this evening so too late to start but tomorrow i'll be having a go at fitting swivel repair kit and new disc, pads, brake pipe and braided hose to near side front of Disco and just repair kit and braided hose to offside as that has new disc and pads on it already

Got inner hub seals for rear as well but think thats goin to be done Friday.

I am doing much the same without the brake bits though. good luck.......You as full of trepidation as me?

 

[Rawly86]

Took It to Rogers of bedford.

 

[big si]

Replaced flywheel oilseal and refitted clutch, time fer a cuppa before the lump goes back in

 

[DJ Xan]

Heater matrix back in
Nice and toasty in there now.

 

[big si]

Gearbox back in and sorted, time to pull the head off.

 

[gemsdad]

Gearbox back in and sorted, time to pull the head off.

durdy bugger.

 

[Silverlandy]

Drove down to Braintree today, left in plenty o'time and managed 125mile round trip on quarter of a tank...really getting into Radio2 now for two reasons, firstly I'm getting old and secondly I have bought a plug in iPhone/**** nav charger and it interferes with KissFM a buggery. R2 is fine though

 

[Dr No]

Stripped the O/S front swivel joint. I'm glad i have an angle grinder, those stupid torx screw heads in the bottom bearing had to be cut through. as did the surrounding metal work. The other bolts were so rusted up i had to use the two spanner 'flat pry bar' method of getting them undone. Now I ain't showing off by saying I used to bench 165kg as a training weight (Fat and old now admittedly). But, I swear it took every ounce I had to get some of them cracked.
Inside the housing everything was mangled. Bottom and top races were in bits, swarf and shards of metal everywhere. Complete rebuild this weekend. Might as well do Calipers and Discs whilst I am at it.

 

[Grahame of the shires]

Done nothing in Keith, (my Discovery, Don't ask about the name) because the wifie nicked it. Almost called the cops but thought better of it!!!!

 

[discostew38]

Fitted the new fog light and re-aligned the front bumper