Search results

What year and spec are the discos your breaking, I would be interested in a few bits if you have them.

So is there any way of using the eas system in the way in which I want to use it. Would I be able to manually controll it with the controll box ?

Hi all thanks for the input, the eas won't be used on a range rover, hence me having to operate it manually. The 12v figure was a guess as I haven't looked into what voltage the system requires for the valves and so on .

Hi all does the eas need a tank/cylinder to work, I am going to operate it manually. Ie seperate 12v to pump and valves ?

hi pal, you will need new head gasket and new head bolts, turner engineering is the best place to buy. As for cam shafts the 10p and 15p are different and cannot be interchanged. you will also need the yellow sealant from turners to seal the cam carrier back down to the head. but to be...

Hi buddy, this is the wrong section to post this so the correct people might not see it ( this is for engines ) But i can tell you i have had a double air bed in the back of a discovery before and you can sleep in it. if that helps :) There was a post on d2bc about using school type table...

Hi again all, has any one used this TOOL for there td5? Just wanted to know the correct porceedure when doing it, ie is it ok to crank the engine with the rocker cover off, as i have the rocker shaft out aswell or will i be covered in oil? would turning over by hand produce enough pressure ?

Cheers buddy, i take it these are the guys who can make them then ?

Hi all i suppose there are loads of winch bumper question, i am after one of these First Four Shadow Tubular Winch Bumper with A-Bar for Land Rover Defender with Air-Con I have a defender bodied disco 2, so my chassis only sticks out 100mm, from my grill and the inter cooler is touching the...

What did you mean buy squeeze the lash adjusters in the vice , i think the second hand replacement will have adjusted in it ? And as for the bits, the oil should be top notch as i cleaned the sump out completely and it has new oil and genuine filter. i also run some wynns tappet quiter oil...

would it be ok if i just put it back together and drive it for a bit as i want to go to billing next weekend and doubt i will get it done by then ? it only going to get worse and score more but i will be replacing it anyway ?

it definatily sounded half or slower than engine speed as you could distinguish the tick tick tick

Well i suppose thats better then ( less money to be spent :) I know that this problem wants to be rectified but am not sure if it was the ticking/clicking sound as it was quite loud, ( could hear it over the revs ) It was at its easiest to here once the engine had been reved and it was...

Ohh ok, so it will just be a case of ringing turners up and ordering some of them :)

Turner cam shafts are £350 and doesnt say they come with the shells? Ebay used cam shaft £50 my thinking is that a used rocker should be fine as it just bolts down.

do you think it would be ok if i replace them with a used good one's (camshaft and rocker shaft. Would the shells from the camshaft in atm be ok or would i have to replace them, as i cannot find them on the web ? Thanks for the reply, i thought the same lol

Hi all, i have just finished a landybuild, (td5) took her out for a spin and there is a new ticking sound appeared in the engine, it sounded top end, there is no relation to anything other than the engine, it wasnt any pullys, so i popped the rocker cover of and found that the 5th cylinder cam...

Yes where the 3rd seats lock into the floor, if you have 3rd row seats. I have just been out and took a few pictures of mine for you :) Measurements where 55.5cm from the inside of the black trim, as show in the picture. And it's 38cm from each side of the car. :)

Hi pal, has been covered here before... But here goes :) I have a cheaper ebay style one on my td5 100" build, runs d2 components I had to trim the rad down slightly on the sides but its only a bit of plastic :) http://i1295.photobucket.com/albums/...psfkz0erlf.jpg...

Does it have ace ?