Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. D

    LR 90 4.8 V8 for sale

    Now sold
  2. D

    Accelerator wont work in gear.

    oops ignore my comments, missed out the last 10 pages of comments!
  3. D

    Accelerator wont work in gear.

    Think you are on the right track with the pressure switch and the failed ones that I have seen have been failing to switch the pump on (as per yours). Not sure how you have done your checks but I would confirm where the problem is by checking to see if the pressure switch is sending a gnd signal...
  4. D

    front wiper problem

    When you switch the wipers off, the becm continues to power the wiper motor until the becm sees a gnd signal from the park switch (in the wiper motor). so using a voltmeter check to see if the becm receives this gnd signal ie voltmeter will show 0 volts. When wiper is not in park position, this...
  5. D

    P38 strange one !

    And presumably you no longer have a "P" in your instrument pack. as in Prndl. sorry could not resist that.
  6. D

    front wiper problem

    Sure? I don't have a P38 and I might be wrong, but I thought that the wipers self parked when the ignition/aux were switched off.
  7. D

    Which Temp Sensor

    If problem goes away when you leave the AFM connector off and also when you disconnect the plug and plug it back in, then I believe you issue is caused by a fault on the AFM “circuit”. I’m more familiar with other injection ecus and these will lock out the AFM for the duration...
  8. D

    LR 90 4.8 V8 for sale

    Time has come for me to part with my beloved project. Any fellow petrol heads interested in my 90? Land Rover 90 4.8L V8 Thor engine Auto ABS-Traction Control | eBay
  9. D

    Engine knocking under acceleration help please

    . Not sure that this is the best thing to do for a catalyst engine with O2 sensors. My vote would be on exhaust leak.
  10. D

    Which Temp Sensor

    Found this site which might be useful for you. Lucas 14CUX Fuel Injection System ? Installation and Diagnostic Notes. Try running the engine and when warm, disconnect the AFM and drive for ~50metres and see if it drives as well as when you do a reset with the AFM. I still suspect that the...
  11. D

    BECM not going to sleep ( it's not the r/f receiver )

    One slight problem, the becm will go to sleep if any of the doors or tailgate/ bonnet is open or closed, locked or unlocked. The key in message is easiest way to see if becm is going to sleep or not, a faint glowing LED on the H gate is to next easiest If you are in P then the P LED will glow...
  12. D

    Which Temp Sensor

    One thing that it's not is the crank sensor as the 3.9 did not have one!. I had the same problem as you with my 3.9 and the engine was fine when the airflow meter was disconnected as the 14CUX ecu then uses the throttle pot to control the fueling. Disconnecting the AFM does not actually reset...
  13. D

    Temperature Gauge

    Buy a resistor between 25 & 50 ohms (for a petrol engine this will give a vertical needle position) and use it in place of the temp sensor. If you have a green temp sensor correct it between the 2 pins of the harness connector. If you have a single wire sensor connect the end of the resistor to...
  14. D

    jap import (speedo)

    Sorry if I confused you, Change the Ipack to a UK one, but when you are using a Nanocom to clear the ODO error message on the Ipack, don't be tempted to try and switch the becm to a UK market setting. This will enable the the EKA system (Japanese vehicles did not use the the EKA system). Do a...
  15. D

    jap import (speedo)

    No need for a convertor the kph & mph Ipacks recieve the same signal from the ABS via the becm.There is a market setting in the becm for Japan but this does nothing for the odometer. You will get the odometer error message when you fit the pack and this can be cleared normally at a dealer (I...
  16. D

    Battery Issue or Starter Motor?

    If you are concerned about battery drain then do a couple of simple checks, make sure the becm is going to sleep correctly by opening the drivers door, leave key in ignition (not in ign or aux position),switch off all lights (including interior lights). When becm goes to sleep the "key in...
  17. D

    3.9 into defender???

    Try and keep the fuel set up as std as you can (either injection or SU carbs). This will give you the best starting, reliabilty and fuel consumption as they are tuned to work together. If you go for the Holley, you may end up with hot restart problems and almost certainly worse fuel consumption...
  18. D

    Which Temp Sensor

    If you think that it's a coolant sensor then warm the engine up and disconnect the coolant sensor. When the ecu sees an open circuit on the sensor, it will assume a default temperature. The engine will not be running at optimum fueling but it should run fine. When you say reset the ECU by...
  19. D

    Alternator Failure???

    The becm needs to see a gnd signal on the charge warning lamp input from the alternator before it will put up a warning message on the ipack. When everything is fine and the alternator is charging then there will be Vbatt on this input wire. With some alternator regulator faults, this signal can...
  20. D

    auto gearbox diy compushift..geeks only..

    The H gate is the plastic housing that sits on top of the gear selector housing/assy. The plastic housing has nothing to do with the selection of high/low (apart from indicating high/low position), that is done with the microswitches in the base of the gear selector housing/assy. The...
Back
Top