Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. 3

    Disco Project :D

    right not been about for a while as i'm mostly over on my little puggy forum and the DOC forum but a quick update :) The engine runs now after i set the static timing up :) all the welding is now done Partially polly bushed F/O/S window reg has been changed front bumper is back on pretty much...
  2. 3

    bobtail discovery build up/project thread

    yup he sold it and got a golf. i think he only did it because all his mates had them, they all got little cars so he sold it and got the same. dont know how much he got for it as after himself and all the kids in their chavved up cars came and made so much noise/disturbance outside my house, he...
  3. 3

    Disco Project :D

    had a day at it today :Dpictures speak better than words but i got carried away and forgeot to take some so i got a vid insted :) Is a little smokey but i'm putting that down to the turbo hoses not being attached. polly bushed the rear ARB to :)
  4. 3

    bobtail discovery build up/project thread

    that looks like the memorial cruise that came through my village that i questioned about in my previous post.
  5. 3

    Disco Project :D

    gettin there, was up at billing yesterday and picked up a timing belt kit, just need a crank seal and the pump back and it'll be finished engine wise, all the bits of trim hafta go back on the boot floor still needs patching as does the front arch , the bottom of the c pillar needs filling and...
  6. 3

    bobtail discovery build up/project thread

    Hey haven't heard from you in a while. what was happnin this evening with all the chavs parking in the road and revving engines and the dangerous driving? i swear i saw you driving accross the village green.
  7. 3

    What have you done to your Landie today.

    put a locking pin in the flywheel :) worked for me Have rust coated the rusty areas in the cab and partially coated the boot floor, started putting ound proofing back into the front
  8. 3

    Disco Project :D

    Well had a couple of hours at it today :) as always i took pics :) Started off by removing all the crap it's gathered over the months Then i cleaned all the dust and dirt out and got busy with the POR15 pretty much all nice and rust proofed now :thumbs then i got busy putting the sound...
  9. 3

    Disco Project :D

    Few pictures courtsy of Mr Lobb and the reason it was leaking, the worn throttle shaft
  10. 3

    Disco Project :D

    So at the moment i'm waiting on the injection pump to come back to me :) it's at a friends in devon getting all the seals replaced and some modifications to the internal workings, then that'll go back on along with a new cam belt kit and rear crank seal :) then it's just the welding that is left...
  11. 3

    bobtail discovery build up/project thread

    looking great :) nice to see it's almost finished :) havent seen you in a while so will have to catch up at some point and i know of some tyres but i dont know if you'd want them X2 Cooper Zeon XST 255 65 16" hardly used 7-8mm £40 each X2 General Grabber AW 255 65 16" sligly used 5-6 mm £35 each
  12. 3

    Disco Project :D

    i do but it's only a medium sized compressor and i have a gun but last time i tried to use it it just kept blocking up
  13. 3

    Disco Project :D

    thanks, i'll look into it, i was just going to use plastic primer then satin black but if i can find satin laquer thats even better :)
  14. 3

    Disco Project :D

    well i picked the bumper up today :) very pleased :) there is so much satisfaction when you pay someone else to do a deicent job :) there is still a bit of pitting but nothing major they even cleaned the threads off for me :) Headlight washers went on new washer pipe (the old stuff had...
  15. 3

    Disco Project :D

    so i got an email off the people powder coating my bumper on the 7th telling me that it would be ready to collect on the 11th, well i couldn't collect because i was getting the car ready for FCS so i rang them this morning to make sure it was ok to go and pick up :) so 20 min drive to the place...
  16. 3

    What have you done to your Landie today.

    did some filling of holes and grinding of metal :D
  17. 3

    Disco Project :D

    So been a long day but not much to show :( Started off by going to the scrappy to get some weldable metal, then for a random drive :S then we got to work :) emptied everytihng out of my shed on wheels and started poking holes in the rust untill we ended up with this Then a bit of fillering...
  18. 3

    Cam Belt kit

    finally getting round to doing this now the island4x4 one is a britpart branded kit and after everyone sayin bad things about them i'm avoiding them :) so i want a deicent timing kit with all the do-da's i should replace and the oil seal on the crank as mine is leaking and the timing cover...
  19. 3

    Disco Project :D

    Well had a day playing with the landy :) first of al;l while i was waiting for some helpers i part polished the bonnet :) Then my mums partner cam over to help shortly followed by michael :) between us we managed to get the crankshaft damper off and the timing cover so went from to need a...
  20. 3

    Disco Project :D

    nothing much to really say, hopefully getting the injection pump off tomorrow and that'll get sent off then i'm just waiting on the welding, powder coaters have informed me that the bumper is ready so that'll prob get picked up on thursday then tha'll have all the plastic and washer jets put...
Back
Top