Search results

Hi my compression test l got was cylinder (1) 200 cylinder(2) 220 cylinder(3)70 cylinder (4) 220 = 2.2bar car was stood for a time ? And has not started in 15 months

Hi its a 2008 if l remove the flaps what would the effect be on the engine what's the point of the flaps Thanks for your help to everyone

Hi thanks but would it start and run

Hi hope someone can give me some advice will a diesel engine start with low compression in one cylinder my mechanic says no and it needs engine replacement

Hi have you looked on disc for version number

Hi I have a2008 freelander 2 and l have searched the entire care for that relay the only one l can find is in the fuse box f1 fuse and relay 4 seems to have something to do with it the four wires from the glow plugs merges into one wire about a 30 cm in the harness going over the starter motor...

Hi thanks for replying l cannot find a glowplug relay only one book says is in the fuse box engine compartment and that just the same as all of them l put a volt meter on glowplug wireing loom turn key in and it reads 10.3volts on each connect pulled out the relay it says is for it R4 and...

My freelander 2 is making me greyer by the day

Hi purchased a freelander 2 automatic 2008 none starter checked it over found all 4 glowplug not working would not light at all so installed brand new Bosch Fast Heat Duraterm Glow Plugs after testing them rebuilt and tried to start no look then fault code came up glowplug fault stripping it...

Hi it's the freelander 2 2008 model under the back seat there's a access panel so there's is one there

Hi l have applied direct 12volts to the rear pump l can here it running but when l take the fuel line off the supply filter there's no diesel so it looks like something is wrong in there now to replace it l will have to take the exhaust off and the prop shaft so is it best to widen the hole...

I don't think that the previous owner knew about it he was a mortgage broker in London said he spent loads on it what ever it needed l had it delivered and the garage did not send me all the paperwork and the spare key now they just ignore my messages about it so l cannot see him messing about...

Hi it looks like it's been butchered it already they have tried drilling it but gone wrong they must have forgotten the broken bolt is harder than the head and gone well off it. thanks kev

No looks like they have tried drilling it out and gone wrong have you any idea has to how thick the head is in that spot do you think l can drill it and put a type of stud in the hole any idea what type of epoxy or glue would hold it in then l can hold it in the right position with a nut...

Hi got a freelander 2 and someone has broken the hold down bolt to a injector and held it down with a small bolt against it l wanted to do a compression test but cannot get a good sealso it must not be sealing right when injector is in can anybody recommend a mobile drill and retaper if there is...

Hi got a freelander 2 and someone has broken the hold down bolt to a injector and held it down with a small bolt against it l wanted to do a compression test but cannot get a good seal so it must not be sealing right when injector is in can anybody recommend a mobile drill and retaper if there...

Thanks for that do you know by any chance where I can get one of theses pipe connectors it's had its top saw off thanks for any help new and trying to find my way round site

Can you recommend a good wiring diagram please

Hi have tried to find a good wire diagram Haynes manual even paid on line to download one but none show the 5volt A diagram good when I got it it was not working they said it was injections I have cleaned and tested them 2 had blocked stream and only one glow plug worked fitted new Bosch...

Hi can anybody help me my freelander 2 2008 cranking but no start fault codes p2564-37 p0340-00 p0380-00 p0642-00 they are all circuit A and state permanent do you think it needs a ECM thanks any help suggestions