Recent content by bakuuu

Do you think isn´t a good business? I think that it is...but first i want to collect some usefull information about the P38 with 4.6 engine

Hi there. I have one 3 door Range rover 3.9i V8 with fully rebuided engine and some extras (35 inch tyres, 15cm lift,extended arches, new paint job, and so on) and i´m looking to change for one 4.6 HSE P38 Range rover from 1996. i haven´t to give any money for the change. What do you think...

What i have to change of one 3.9i V8 manual range rover to fit an auto gear box? it´s expensive?

CharlesY, No comments! Thank you for your replies. My idea is put the supercharger, jaguar xk8 nozzles and remaped ECU. my idea is 250HP +-. i´m rebuiding my another 3.9i v8 engine, and i´m serious thinking put the supercharger,but i have some afraid because the engine healthy. This is a range...

hello someone had supercharged one rover v8 engine? i´m thinking to install one M112 eaton supercharger from a Jaguar with low pressure (maybe 0.5BAR) to not destroy the engine. it´s simple? what i need to put the supercharger in the v8 engine? regards

hi i will do a rebuild of my v8 engine too. can you tell me where you bought the v8 components? RPI engineering?

Thank you for the comments. i bought this kit Bespoke Rover V8 Camshaft replacement Kit RPi Specail on eBay (end time 11-Oct-10 11:11:14 BST) I need the main bearings and rockershafts only to complete this "stage". then, i will try to put a jaguar supercharger (EATON M112) with low boost. what...

Thank you for the answers. Norseman thank you for the wellcome ;) I think you can understand my english...at least i try...:) vougese39 thank you. it´s what i will make. I don´t want make a FULL restoration...only a small revision because my acttual V8 engine makes a strange noise. (TAC TAC...

Hi there. i´m from Portugal, sorry my english. I bought in ebay UK one 3.9i engine for make one small restoration on it and extracte some extra power. What do you suggests to upgrade / change? I´m thinking: head area: - take off the heads, change all gasket and seals - new rocker shafts -...

i have the same problem than you...i hear a TAC TAC TAC when the engine is in iddle, but the noise appears only when the engine is hot!:mad: Try the main bearings from the camshaft.

Hello I want to put in my 1992 Range Rover V8 3.9EFI a rear salisbury axle. can i fit the rear axle from the 109" from 1975? It´s easy to install? what i need? I want a stronger axle (my axle has 10splines halfshafts) thank you

with ONLY petrol, the noise is the same...when the engine is hot, the TAC TAC TAC comes in idle:( another thing: my 3.9i engine is very very slow...for example in the highway, in 5th gear, i can´t go at 60 MPh when is in one small rise...i have to reduce for 4th, and some times to...

Thank you for the post. The noise is very low..Inside the car i can´t hear anything, only outside. I hear the noise since i bought the car, and i done 5000miles +/-, and the noise kept the same (neither lower, neither higher). So, i have to change the rock arms RV8 Rocker Shaft+steel arm kit -...

thank you for the answer. I think that isn´t the cam followers. if the problem are the cam followers,they should make the "tac tac tac" with the engine cold right? The "tac tac tac" only appears when the engine is hot..

Hello i have my range rover 3.9i v8 with LPG converted and ,here in Portugal, some mechanics tell me that it "kill" the engine. My range rover have 155 000 KLM (about 75 000 miles). One strange noise that i ear is "TAC TAC TAC" when the engine runs in idle (only when it is hot. when the engine...