Latest activity

Hi all, looking at attempting to replace the rear bushes on the front lower suspension arm. Anyone know if this can be done without taking the arm out completely? Can’t seem to find any details on here or anywhere else. The bushes are available...

Venison from the garden…? Very posh

Any photos?

I hear that a lot - but ageing parents is one thing, and the other is that life here isn't all safaris and sunsets; there is a lot that doesn't get published in the news, which is very, very tough. Everywhere seems a bit broken at the moment, so...

Having venison liver and onion with new potatoes and mint , Swiss chard all from the garden 👍👍

Ha - outside Nairobi near Rongai - karibuni :-)

No pleasing some folk no matter what you do 😈

Doesn’t sound normal to me!

The knocking was a brand new (aftermarket) top mount/bearing. Switched it for a LR genuine o e at it stopped. The ‘wobble’ is/was not related AFAIK. I had a fully recon’d and updated front PTU fitted (due to wear on the splines) during the refit...

Hey guys...I have a 2012 SD4 SE. When driving over a speed hump at anything faster than a trot the front shocks topping out with a solid THUNK. Apparently this is "normal" from new. Is there any aftermarket shock, or bump stop or whatever, to...

We has gone past page 6666

First check the tank for cracks or crazing, also check the cap, make sure there is red coolant in the car not just water, next check the hose going to the Y section on the head the seal can leak and you lose coolant. 1 2 3 make sure there is...

As a rule, all the airbag sensors get corrosion in the plugs as most 38's take on water... Cut the plugs and hard wire them with either solder or good butt connectors. Its rare the actual airbags fail. Once done clear the faults and go from...

There’s 4 variations of D1 tail lights in the life of the 300 series 1995 to1998. So based on 96/97 MY for UK & the rest of the world the part numbers are PRC6475 RH and PRC6476 LH As always to get the correct part the VIN No is required.

update, i have shelved the extractors i cant be bothered, maybe i may sell them on or keep them

I'll have a look tomorrow, not sure if the one I have, are the whole unit or just the lenses.

Thats nice good luck mate lol. Now I see why you want a sheetbox to weld as you want a good excuse to get oot the hoose. 🤣🤣

Hi, Got a confusing issue with my FL2 TD4 Manual XS 2012. When the car is first setting off and the engine is cold, I get a Judder when lifting the clutch between 1st and 2nd gear. This only happens for the first half ISH mile and then the car...

Hi, Since i bought my p38 2.5dse 1995 it shows an airbag fault. Nanocom gives the next codes: -drivers airbag measures open circuit -passenger airbag measures open circuit -left hand crash sensor measures open circuit -right hand crash sensor...

Hi there Did you ever get this problem fixed? If so what was the fix as I'm having the exact same problem and had the exact same stuff done to mine? Please can you help! Thanks

No, missus having 3rd kid in 2 weeks and I’m losing my mind hahahaha! I’ve not actually seen that one but I bet it will probably hit 7/8k

Where's @WhiskyLassie @DevonGuy @derwendolly, all ok we hope. :)

Is everything alright at home ?? 🤣 🤣 Bid on this if you've got the funds...

Hi Nodge68 I'm not sure but I could find out, do you know which is the correct gearbox fluid that should have been used please?

Sticky butyl sheeting or mats will dampen the 'dwang' from areas like the sides, wheel arches and roof. These are available from a number of resellers. I've bought from DoDo ...

Deffo the truck :cool: :cool: you need a a big space for them lifts, single poster lifts are available with 4 arms was thinking of getting one for my garage once its finished.

I gotta ask, am I delusional or are a lot of the current sellers of D2’s? Cause I’m seeing D2’s for like 3-4k that does not mention anything to do with welding the go-to places on a disco, it does mention about how all the filters have been...

I believe standard are actually M12 heads as I had an M12 socket get stuck on the head of the bolts when it snapped . Obviously this is totally different if the exhaust was changed in the past and someone used different bolts. However M10...

You’ll like this ‘un then… Dunno if I want the truck or the lifts more…

Hello everyone, It’s me again! I want to change all of my engine mounts but I don’t know how many of them are under the bonnet? Model: Freelander, 2.0 DI, 1999., 3-door, 72kW (98HP) Thanks a lot! and sorry for my bad english, I hope you will...