WTB: Disco 2.0 MPi inlet manifold
- Thread starter autopia
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
storm99
Spreading Joy & Harmony
- Posts
- 21,065
- Location
- Brexited. Living on an island.
Go ahead, you don't need permission but nice of you to ask.
Sincere regards.
Sincere regards.
Apologies for not checking that I could ask the question before posting it.
Great forum, but I couldn't find the for sale/wanted section, so thought the Discovery board was the best option, if my enquiry contravenes forum rules or etiquette, then please go ahead and delete it.
best regards
Great forum, but I couldn't find the for sale/wanted section, so thought the Discovery board was the best option, if my enquiry contravenes forum rules or etiquette, then please go ahead and delete it.
best regards
stuart4884
Member
- Posts
- 73
- Location
- Sheffield
Hi I have a complete MPi engine where are you located
cheers Stuart
:doh:
cheers Stuart
:doh:
GRATCH
HUGE MEMBER
- Posts
- 15,502
- Location
- North Cheshire
See the red defender at the top of the page? If you look below it's front wheel you'll see where it says 'For Sale', click on it.
storm99
Spreading Joy & Harmony
- Posts
- 21,065
- Location
- Brexited. Living on an island.
This is all very polite. How unusual...yet strangely therapeutic..
Deepest warmest sincere regards.
Deepest warmest sincere regards.
stuart4884
Member
- Posts
- 73
- Location
- Sheffield
Hi sorry about the delay in getting back to you
anyway you can have the lot for £30 BUT YOU WILL HAVE TO COLLECT
I dont have the time unfortunately. Im not too sure if I can put my
hands on it but I do have the front pipe including the cat
the engine did run o/k was changed for a TDI
Cheers Stuart:doh::clock::ballchain::confused2:
anyway you can have the lot for £30 BUT YOU WILL HAVE TO COLLECT
I dont have the time unfortunately. Im not too sure if I can put my
hands on it but I do have the front pipe including the cat
the engine did run o/k was changed for a TDI
Cheers Stuart
:doh::clock::ballchain::confused2:Beast o Bodmin
Banned
- Posts
- 17,157
fit V8
stuart4884
Member
- Posts
- 73
- Location
- Sheffield
Hi I live in Sheffield 1Mls Jnc 25 M1
my phone No is 0114 2576740 / 07810311260
Cheers Stuart:doh::flame::confused2:
my phone No is 0114 2576740 / 07810311260
Cheers Stuart:doh:
:flame::confused2:
stuart4884
Member
- Posts
- 73
- Location
- Sheffield
Cheers mate never thought about that must
be summat to do with my age senilty.. now what was I on about
Cheera Stuart:doh::doh::doh:
be summat to do with my age senilty.. now what was I on about
Cheera Stuart:doh::doh::doh:
Weslake
New Member
- Posts
- 2
- Location
- Nottingham
Sorry to bump this post, but if anyone else has an inlet manifold for an Mpi, I need one. Owned land rovers, from defenders, discoveries and finally later Freelander from 1993.
Many Thanks, Mark
Many Thanks, Mark
- Posts
- 9,105
- Location
- Roaming the UK on assignments
You'll be hard pressed to find one these days.
Might be worth a look to see if you can find a 620 with a T series 2ltr engine in, manifolds can't be too different?...
Weslake
New Member
- Posts
- 2
- Location
- Nottingham
They’re the other way around, as in the intake runs over to the rear of the engine as opposed to the Mpi running towards the front.
I’m fitting a Rover T16 engine - same thing as in the Land Rover, into my MGB hence looking for an Mpi manifold. I can retain the Rover intake but would have to lose my heater box.
I’m fitting a Rover T16 engine - same thing as in the Land Rover, into my MGB hence looking for an Mpi manifold. I can retain the Rover intake but would have to lose my heater box.
- Posts
- 9,105
- Location
- Roaming the UK on assignments
I have to admit that I would be going for custom header and collector to give max torque and gas flow, yes it can be expensive but the difference between factory cast and custom header will be night and day.
