Worn engine mount bushes

Northern Irelander · Apr 6, 2013

Ahem !
Here's one I made earlier
http://www.landyzone.co.uk/lz/f9/k-series-engine-mounts-34139.html

Those PU are a rip off (OE £30ish includes the metal bar)
plus far too hard for an engine bush

WLJayne · Apr 6, 2013

I did see that mate

, I'll try the PU - see how it works but I know it might not be a cure all.

Northern Irelander · Apr 6, 2013

It will let too much engine harmonics through, trust me, I did much trial and error, eventually ditching composite designs for all silicone ones, still going strong 6yrs later.

Plus not all tie bar bushes or gearbox mounts are the same diameter across MG, Rover and LR range.
49mm is a figure that springs to mind for larger tie bar bush????

WLJayne · Apr 7, 2013

What type of silicone dod you use, and what shore hardness was it?

matt1295 · Dec 31, 2013

sorry to dig up an old thread but what did you use to do the cuts in the poly bush my big bush has play in it was going to order a bush but need to make sure i can sort the groves out in it first

Arctic2 · May 7, 2015

Tried those yellow bushes and they are to hard get to much vibration off them, but at the time I did have trouble with the rear diff mounts also so may try them again

QBDoctor · May 7, 2015

Anyone know where I can get the bushes - both the large one & the small one? I rang powerflex & they told me they don't do em

Cheers
Simon

Nodge68 · May 8, 2015

QBDoctor said:
Anyone know where I can get the bushes - both the large one & the small one? I rang powerflex & they told me they don't do em

Cheers
Simon

Ebay

http://www.ebay.co.uk/itm/121605120375?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
This is for the larger bush. The small bush never fails.
Ps. you still on UKCAF?

QBDoctor · May 8, 2015

Nodge68 said:
Ebay Powerflex Bushes Engine Mount Stabiliser Large Rover 200 1995 - 1999 | eBay
This is for the larger bush. The small bush never fails.
Ps. you still on UKCAF?

Thanks for that - sadly the small bush got a bit mashed when the bolt through it worked its way out so I need to replace it.

I am still on UKCAF but I haven't been doing any admin over there for a while due to having been rather unwell for a while - getting better though

Cheers
Simon

Nodge68 · May 8, 2015

QBDoctor said:
Thanks for that - sadly the small bush got a bit mashed when the bolt through it worked its way out so I need to replace it.

I am still on UKCAF but I haven't been doing any admin over there for a while due to having been rather unwell for a while - getting better though

Cheers
Simon

I'll look out the smaller bush for you

I've not been on UKCAF for a few years now after I got dragged into something I'd rather been kept out of. Never mind, that's life I guess. I still have my beautiful WW equipped XS20.
Give me a couple of days and I'll find a bush supplier for you, hope you get well soon

Nodge68 · May 8, 2015

Here you go. Found a complete tie bar for you. KKH102260 | Engine Mount Tie Rod Frl1 - Land Rover Part KKH102260

The part number is KKH102260 if you fancy searching for yourself

Worn engine mount bushes

Northern Irelander

Well-Known Member

WLJayne

Well-Known Member

Northern Irelander

Well-Known Member

WLJayne

Well-Known Member

matt1295

New Member

Arctic2

Well-Known Member

QBDoctor

Member

Nodge68

Well-Known Member

QBDoctor

Member

Nodge68

Well-Known Member

Nodge68

Well-Known Member

Similar threads