jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
try it in gear and with t/box in hi with clutch pressed
whiney as hell
- Thread starter metallicachick86
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
metallicachick86
New Member
- Posts
- 1,308
- Location
- Bury, Lancashire
Yup. Still noisy.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
check fan belts etc aren't rubbing If it's doing it whether it's moving or stationary it usually points to engine related problem.
metallicachick86
New Member
- Posts
- 1,308
- Location
- Bury, Lancashire
My brother is supposed to be coming having a look at somepoint. Il get him to stick his head under the bonnet whilst i rev her us. See what he thinks. So far he has suggested an engine problem, a clutch plate priblem or a flywheel problem.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
+1 on that diagnoses..
You should only change from hi to lo at very low revs and when stationary. with all wheels stopped.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
flywheels dont usually give issuses, clutch plates do which would tie in with clunky gear change ,though you may have more than one issue ,in gear with clutch pressed means no drive at all through gear box ,in neutral gear box is still turning
metallicachick86
New Member
- Posts
- 1,308
- Location
- Bury, Lancashire
https://www.youtube.com/watch?v=l6-Mrsi4sCc&feature=youtube_gdata_player
Not sure if this link will work or not.
Not sure if this link will work or not.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
That doesn't sound good.
metallicachick86
New Member
- Posts
- 1,308
- Location
- Bury, Lancashire
Nope lol. Need it for my holiday in 4 weeks and have no pennies due to paying 500 to get it back on the road a few weeks ago.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
If it is Transfer box. I have a spare that you could use until such time as you can source a replacement.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
id definately be looking over the engine ,fan belt off and try ,rocker cover off etc ,does it run ok or lumpy
metallicachick86
New Member
- Posts
- 1,308
- Location
- Bury, Lancashire
metallicachick86
New Member
- Posts
- 1,308
- Location
- Bury, Lancashire
Seems to run well enough. A bit shaky when pulling away sometimes but this has happened since the new clutch was fitted.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
its hard to tell from recordings but sharp knocking can come from broken rocker or bent push rod etc but would effect running ,same noise can come from vac pump but no effect on running its a matter of working along till your left with only possibility ,shaky ?should be smooth with new clutch ,that may lead you to suspect to clutch issue ie not fitted correct or faulty
metallicachick86
New Member
- Posts
- 1,308
- Location
- Bury, Lancashire
The day after the clutch was fitted, the new bearing collapsed so theu had to take it all out again and refit a new bearing. They checked it all and said it was fine. Its a land rover specialist who fitted it
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
but it felt "shaky"still?
metallicachick86
New Member
- Posts
- 1,308
- Location
- Bury, Lancashire
Yeah. And it still taps. But they just said its probably bedding in.
metallicachick86
New Member
- Posts
- 1,308
- Location
- Bury, Lancashire
Had a similar problem with the old landy but it ran fine despite the tapping.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
still taps ?
