What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Little 6k service.

Oil + Filter
Fuel filter
Air filter
Checked axle oil levels
Cleaned axle breather pipes out
Swivel pin housing topped up with one shot grease

Running better already
 
Tried my best to polish and clean it and make it look presentable as I have to drive in a funeral preseason on Friday. Don't know if I will blend in too well :/
 
Oldseadog said:
How far are you from Shipley? If you are close enough you could send Nrgserve a PM ... He's a good lad and might be able to help you out ;);)
Click to expand...


so i hear his name has been whispered in my ear lol not too far at all about 20 miles and i do need the help just cost me £278 to have work done on her today, £210 of that was labour!
 
Got my tangiers orange mixed up today in Newton Abbot, bit darker than I expected, now to decide what to spray?
My vinyl number plate arrived so that got attached to the vent, why couldn't land rover have made these the same size as a standard number plate.
And fitted the replacement temp sender to find that the gauge is still swinging right up to full.
 
MR BFG said:
Got my tangiers orange mixed up today in Newton Abbot, bit darker than I expected, now to decide what to spray?
My vinyl number plate arrived so that got attached to the vent, why couldn't land rover have made these the same size as a standard number plate.
And fitted the replacement temp sender to find that the gauge is still swinging right up to full.
Click to expand...

you mean to hot? if it does it with just the ignition on and not the engine, then it's probably earthing out or the sender has no resistance.
 
gemsdad said:
tis a well know fact that red landy's do not go up hills.i am in for a shock when i get mine back from james martin.:eek:
Click to expand...


oh right never heard that! lol

no its not red its the one in my avatar and wasn't red before although does have some bits of red paint on it now does that count? :D
 
trax said:
you mean to hot? if it does it with just the ignition on and not the engine, then it's probably earthing out or the sender has no resistance.
Click to expand...

Ignition on goes straight to hot, I replaced the sender in January as the other wouldn't let the gauge move at all, that packed up on Christmas morning, gauge worked fine between June and then even after the 200 conversion in September, I used the petrol sender in the 200 to match with the gauge. New sender in January chucked the needle right round as far as the needle would move with just ignition on even first thing, new one does the same but a lot slower.
I have checked the wire between sender and gauge and that is fine, also ran a new test wire from sender to gauge and same result.
 
MR BFG said:
Ignition on goes straight to hot, I replaced the sender in January as the other wouldn't let the gauge move at all, that packed up on Christmas morning, gauge worked fine between June and then even after the 200 conversion in September, I used the petrol sender in the 200 to match with the gauge. New sender in January chucked the needle right round as far as the needle would move with just ignition on even first thing, new one does the same but a lot slower.
I have checked the wire between sender and gauge and that is fine, also ran a new test wire from sender to gauge and same result.
Click to expand...

Have you got a multi meter? test the resistance from the wire into the back of the gauge to sender (when its removed from gauge), if its low (few ohms) then remove it at the sensor and test again, it should have no resistance. if it still reads only a few ohms its the wire

You could also test the sender by removing the wire and seeing what resistance its reads.

If there all fine then its the gauge, which can be tested by putting a resistor from ground or live (which ever goes to the sensor, which is probably ground but check) you could try a veritable resistor (twisty thing)
 
Over the last couple of days I have put the gearbox back In.
Built the engine back up. And made a couple of brake pipes up for the back axle.
Getting there slowly :)

DSCF1903_zpsf04a16ae.jpg
[/URL][/IMG]

DSCF1905_zps7e0d62b4.jpg
[/URL][/IMG]

DSCF1904_zps4fdfbf28.jpg
[/URL][/IMG]

DSCF1907_zpsa2fdd7fe.jpg
[/URL][/IMG]

DSCF1909_zps4cbb4724.jpg
[/URL][/IMG]
 
You must log in or register to reply here.

Similar threads

C
Freelander 1 crank no start
Replies
0
Views
428
chazy
C
1988smithy
Hill and Ditch 4x4 28th April 2024
2
Replies
29
Views
1K
kermit_rr
kermit_rr
Dabbster
L320 2.7 Fuel fault
Replies
4
Views
519
Dabbster
Dabbster
S
Bulkhead swap 300TDi Defender
Replies
15
Views
2K
trax99
trax99
F
freelander td4 2002 steering shake when going uphill?
Replies
7
Views
449
frenchdave
F
Back
Top