What have you done to your Landie today.

Seein as the bastard V8 wouldn't start again today, even after new leads and coil and a good kickin, then it's comin out and a doozel goin in asap, am flippin fed up of it an it's electrical gremlins, everythin is caked in old mud and rottin away as I look at it.
So TDi goin in and gonna sell it when it's up and runnin.

klandyg said:

I've laid Mine to rest on the front path cos the poor thing failed it's m.o.t and can't come to the lakes for some easter Fun. front wiper motor can be sorted but havin issues tracking down the cause of the high CO2 reading. no faults, runs fine. mechanic has thrown the towel in and recons its a re-map thats required. any ideas?

Click to expand...

Hi klandyg
You might have better luck in getting help if you tell everyone what vehicle you have and whereabouts in the country you are located. Posting in the specific vehicle section could help too.

Hope you get it sorted.

spent the morning stripping the interior out of the back of the disco to see how bad the tin worm is..
lordy has he been hungry.
looks like a new boot floor and a loads of other bits of welding next week then.. dont you just love old disco's:violent:

cleaned the rear floor of the 90 out was full of mud, then got 90% of the roof bolts out for tomoz so my roll cage/hoop can go in just hope the rain stays of!!

half finnished my new rear door trim, varnished the drop down stove holder just waiting on hinges and catches in the post.

Done a total refirb of the brake master cylinder and bled the system between rain storms.
Ready to road test tomorrow.

Fumbled with some nipples and squired my stuff in them. Tomorrow more of the same LOL

fitted this little lot today

staying at standard height with the springs, HD for the winch/ winch bumper, with long travel shocks only 2+ though, so put the cones in just incase they pop out, forgot to buy front spring retainers though!!







only got those photos, forgot to get one with them fitted!!!

also fitted a newer lockable filler cap and pipe!! and new reversing light, just need to do my front pads tomorrow as saw they are low today!

klandyg said:

I've laid Mine to rest on the front path cos the poor thing failed it's m.o.t and can't come to the lakes for some easter Fun. front wiper motor can be sorted but havin issues tracking down the cause of the high CO2 reading. no faults, runs fine. mechanic has thrown the towel in and recons its a re-map thats required. any ideas?

Click to expand...

Find a friendly MOT tester who'll stick the probe up another cars exhaust! LOL!
Heard of it happening a few times!

took it to a garage so it could fail its mot. fitted new washer jet, found out where the fuel leak is, decided that the "spare landrover" is now about to be canablised for its fuel pump, and now need advise on how to change the bush on the a frame

lr110 said:

took it to a garage so it could fail its mot. fitted new washer jet, found out where the fuel leak is, decided that the "spare landrover" is now about to be canablised for its fuel pump, and now need advise on how to change the bush on the a frame

Click to expand...

Assuming it's thee balljoint thats gone it'll be blindingly obvious soon as ya have a look at it.

yer just had a look, a little bit of spanner ****ing thats all

Extended axle breathers, that's about it!

Yesterday one o' me mates brought 'round the rear cross member and chassis legs he made fur me...











Got a bit o' a shock when ah went tae lift the x member.. it's made from 6mm box section!!
Just need tae get me arse intae gear and do some cuttin' and weldin'

bustersbus said:

Yesterday one o' me mates brought 'round the rear cross member and chassis legs he made fur me...

Got a bit o' a shock when ah went tae lift the x member.. it's made from 6mm box section!!
Just need tae get me arse intae gear and do some cuttin' and weldin'

Click to expand...

Oooo your going in for this reverse Ram raiding with that crossmember.....

Sirus said:

Oooo your going in for this reverse Ram raiding with that crossmember.....

Click to expand...

Shhhhhhh.... don't tell everyone!!!

Removed the plastic outer sills on the Disco and had a looksee ... putting a thread up about it on Discovery section ...

fitted me roll bar

fitted me CB, and whip

Noice roll bar!