egor8384
Well-Known Member
- Posts
- 1,427
- Location
- Dartford, Kent
Went and got couple of bits out of thr wreckage. Relay makes me realise how lucky we were
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
I got rabbit blood all over the floor………probably shouldn't have hit it with that second 12g shell 
lyron
Active Member
- Posts
- 536
- Location
- ibstock liecestershire
sorted oil leak on vacume pump. and reset tappets, still bloody noisey though
Jacobjsg
New Member
- Posts
- 2
- Location
- Springfield va
Was wondering if anybody can help I recently replaced all four air suspension with an arnott gen 3 and rebuilt my compressor also the valve block was rebuilt. When left to regular ride height right side of the vehicle saggs front right and rear right could not find any leaks or hear air leaking not sure if this can be a height sensor or a valve. I do have an eas kicker check for faults no faults. When I drive the range everything operates normal.
West Slope Rover
Well-Known Member
- Posts
- 8,617
- Location
- deep underground
Wrong place for this, mate. Head on over to "Introduce Yourself" and do just that. Let the peeps say their hellos or **** offs and then go to the proper forum section for your Landy and then ask your question.
Oh ya, I changed my oil and filter and checked all the fluids.
fishsponge
New Member
- Posts
- 1,432
- Location
- Cambridgeshire, UK
just secured both my batteries ready for the new MOT rules!
SHORT ROUND
Active Member
- Posts
- 675
- Location
- forest of dean, gloucestershire
replaced both front oil seals and wheel bearings
Mark L
Well-Known Member
- Posts
- 2,693
- Location
- Tamworth - Staffs
Re-sealed the back doors after they were trimmed for fitting the wide arch kit.
Some Evo-stick, a bicylce inner tube, gaffer tape, marine sealant and the job's a good 'un.
Oh, and relocated the original rubber door seals to help keep the crap out.
Some Evo-stick, a bicylce inner tube, gaffer tape, marine sealant and the job's a good 'un.
Oh, and relocated the original rubber door seals to help keep the crap out.
Hamsterberg
Well-Known Member
- Posts
- 2,076
- Location
- Essex
Ive got a pair of axles that i had shot blasted and picked up yeserday. so yesterday i got two thick coats of epoxy paint (yellow) on and today a nice gloss black top coat, very happy with results, chassis go's off for galvanising tomorrow and back wednesday
) on and today a nice gloss black top coat, very happy with results, chassis go's off for galvanising tomorrow and back wednesdayandyjd
Member
- Posts
- 79
- Location
- Dunedin, New Zealand
Checked fluids under the bonnet and check condition of air filter. Need to get a new oil filler cap.
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
Sunday afternoon walk 15th April 2012
aw68
Member
- Posts
- 30
- Location
- derbyshire
Just got back from the garage.... I am now the proud beholder of 12 months MOT on my 110! Yesssssss...! I feel like a proud parent.
Hamsterberg
Well-Known Member
- Posts
- 2,076
- Location
- Essex
Found out today that the front axle i had shot blasted and i epoxy painted is no good as it has no anti roll bar brackets
disco147
Well-Known Member
- Posts
- 1,147
- Location
- Chichester, West Sussex
fitted a new indicator stalk... hardest part of it was getting under the bonnet as the bloody catch had siezed! :-/ 20 minutes and a lot of WD40 later and I managed to disconnect the battery! lol... put a longer cable on my cb aerial as well, 6 metres does the job nicely
just gonna check its still tuned in nicely in a minute!
just gonna check its still tuned in nicely in a minute!
