What have you done to your Freelander today

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Getting new centre and back exhaust fitted, a plastic wheel arch trim fitted to replace the damaged old one, three new tires on and the tracking sorted
 
Replaced all the diff mounts .
Not as hard as I thought and I didn't take the prop off first just moved it away with a pry bar and wiggled the front mount in:)
 
Singvogel said:
I had code p0240 a week or so back, after a long high-speed journey.

I checked the turbo hoses for holes/splits and clips/clamps for tightness, and it turned out one hose (the 90degree bend one) was a cm too short and despite keeping on re-positioning it and re-tightening the 'T'-Bolt clamp on the beggar, it was determined to slide off.
Click to expand...
Singvogel said:
:(

Problem solved - phoned Gareth at DPH yesterday - replacement hose arrived this morning. Hows that for service - well done DPH! :clap2:

Now fitted - all is peachy-dandy again. :D

Singvogel. :cool:
Click to expand...
Was it too short as supplied? Should I check mine for length before fitting ?
Thank you.
 
Re: 90 degree bend turbo hose from DPH.

JonFre said:
Was it too short as supplied? Should I check mine for length before fitting ?
Thank you.
Click to expand...

Yes, it was supplied short - Gareth gave me an honest response of 'human error' and sent a replacement immediately. Presumably a one-off mistake.

It fitted the plastic ducting no problem - it was at the other end where it didn't go far enough on to the EGR by-pass so the 'T'-clamp was right at the edge of the metal.

My today's news is an MOT rejection / failure - rusty front brake pipe. :(

Singvogel.
 
Singvogel said:
Re: 90 degree bend turbo hose from DPH.



Yes, it was supplied short - Gareth gave me an honest response of 'human error' and sent a replacement immediately. Presumably a one-off mistake.

It fitted the plastic ducting no problem - it was at the other end where it didn't go far enough on to the EGR by-pass so the 'T'-clamp was right at the edge of the metal.

My today's news is an MOT rejection / failure - rusty front brake pipe. :(

Singvogel.
Click to expand...



"Freelander " "rusty " Shirly not? :eek:
 
Drove it after fitting the new hoses yesterday,,,:dance:
Great car and now very different..:crazy_driver:
 
Singvogel said:
Re: 90 degree bend turbo hose from DPH.



Yes, it was supplied short - Gareth gave me an honest response of 'human error' and sent a replacement immediately. Presumably a one-off mistake.
Click to expand...
Singvogel said:


It fitted the plastic ducting no problem - it was at the other end where it didn't go far enough on to the EGR by-pass so the 'T'-clamp was right at the edge of the metal.

My today's news is an MOT rejection / failure - rusty front brake pipe. :(

Singvogel.
Click to expand...

Thanks for the info. I will compare my silicon elbow with the old original before fitting in case some have been cut short. Sorry to hear about the mot failure, maybe it's all the salt that's used north of the border!
 
JonFre said:
I would think you are even more mad about the missing wheel caps, I know I would be. I suppose they will be on ebay soon.
Click to expand...

Yes - this is turning out to be not my week at all.

Don't mention wheel-caps - :mad::mad::mad::mad::mad:

They are only a £10 or so on eBay to get replacements - maybe my own back - I need to check if anyone up here is selling them 'collect in person'.

S.
 
You must log in or register to reply here.

Similar threads

B
Freelander 1 Freelander prop bearings replacement td4
Replies
15
Views
603
andyfreelandy
andyfreelandy
O
Freelander 2 diff removal
Replies
7
Views
331
Nodge68
Nodge68
andyfreelandy
Other New Project starting today
Replies
3
Views
325
Alibro
Alibro
P
2006 Facelift TD4 Auto turbo vacuum boost solenoid
Replies
11
Views
577
andyfreelandy
andyfreelandy
P
Freelander 2 4wd problems
Replies
3
Views
675
pauld2296
P
Back
Top