- Posts
- 5,698
- Location
- North Manchester
Cleaned the windows. Still waiting for them to re open the motorway. What to do next
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,263
- Location
- Trapped inside my head @ LZ asylum
@backinblack
You must be going mad by now, atleast you are in one of your favourite places
Set all variations of radio station so you got alternatives when actually driving??
You might have enough time strip the heads off
You must be going mad by now, atleast you are in one of your favourite places
Set all variations of radio station so you got alternatives when actually driving??
You might have enough time strip the heads off
- Posts
- 5,698
- Location
- North Manchester
I must admit I am bored enough to get the hand book out of the glove box and see what half of these buttons do.
Can’t play too much. My fuel light has come on and I don’t want to flatten the battery.
As you say it’s the best chair to sit in for an hour.
Can’t play too much. My fuel light has come on and I don’t want to flatten the battery.
As you say it’s the best chair to sit in for an hour.
- Posts
- 18,963
- Location
- Buckinghamshire, UK. ('95 DT)
No, it'll wait until you're at your most vulnerable.
- Posts
- 5,698
- Location
- North Manchester
Didn't get time to fit the new brake pads I got last week, toy police turned us all round and escorted us south on the north bound carriageway.
Mukiwa
Well-Known Member
- Posts
- 469
- Location
- Winsford, Cheshire, near Oulton Park
Fuel injection pump:
Took 6 hours to remove all the rubbish and go to Halfrauds for the 17mm sump tool to remove the tension pulley. Changed all the o rings, installed a viton on in the HP head and drinking a cider for a job well done. What a ****ty job.
Tomorrow as Mr Haynes once said "fitting is the reverse of removal". We'll see
Took 6 hours to remove all the rubbish and go to Halfrauds for the 17mm sump tool to remove the tension pulley. Changed all the o rings, installed a viton on in the HP head and drinking a cider for a job well done. What a ****ty job.
Tomorrow as Mr Haynes once said "fitting is the reverse of removal". We'll see
- Posts
- 18,963
- Location
- Buckinghamshire, UK. ('95 DT)
Fuel injection pump:
Took 6 hours to remove all the rubbish and go to Halfrauds for the 17mm sump tool to remove the tension pulley. Changed all the o rings, installed a viton on in the HP head and drinking a cider for a job well done. What a ****ty job.
Tomorrow as Mr Haynes once said "fitting is the reverse of removal". We'll see
Think I might have used a bolt with the right sized head and 2 nuts on it.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,263
- Location
- Trapped inside my head @ LZ asylum
I had issues with that when I snapped my tensioner. Tried going cheap but bought laser bmw sump tool especially, glad I did it needed about 200nm to crack it off -
@kds - still not found end of that spanner, it’s in engine bay somewhere?
So the bu**er won't let go
Snapped the 89p rad key, got a BMW/MG 14/17mm hex plug which snapped the spanner
View attachment 171305
Then only the whole oily bloody thing would come out of the block
View attachment 171304
View attachment 171306
So I remembered you saying you had to cut...
View attachment 171308
Hope I'm not missing a point (other than the spanner ; yet to be found
@kds - still not found end of that spanner, it’s in engine bay somewhere?
RangeRoller dt
Well-Sprung Member
- Posts
- 14,263
- Location
- Trapped inside my head @ LZ asylum
Today I dropped the oil and flushed it out with fresh and a ‘cleaning agent’. Jacked two front wheels up to try tip as much as possible out of the rad. I’ve left it overnight with a pan underneath see how much drips out slowly.
This made it possible to locate my worn UJ’s on the shafts. I’ve had problems identifying what it was in the past but with both wheels up and my head near the sump it was literally right in front of me.
Haven’t got a (15mm?) spanner to get access to the bolts as they are really tight. So I’ve opted to take it off at the joint for now so I can crack them off easily. I got all four wheels up before I worked out the handbrake was holding it
Surprised how the clips came out with just a bit of wiggling, suppose this is what it’s like when you actually have the right tool for the job
The adventure continues tomorrow when I go hunting for new UJ and try to put oil back in without something going catastrophically wrong as usual
Wish me luck
This made it possible to locate my worn UJ’s on the shafts. I’ve had problems identifying what it was in the past but with both wheels up and my head near the sump it was literally right in front of me.
Haven’t got a (15mm?) spanner to get access to the bolts as they are really tight. So I’ve opted to take it off at the joint for now so I can crack them off easily. I got all four wheels up before I worked out the handbrake was holding it
Surprised how the clips came out with just a bit of wiggling, suppose this is what it’s like when you actually have the right tool for the job
The adventure continues tomorrow when I go hunting for new UJ and try to put oil back in without something going catastrophically wrong as usual
Wish me luck
Last edited:
kds
Well-Known Member
- Posts
- 2,218
- Location
- old,ugly, tired in Lincoln.
Just as long as its not in the engine you`ll be fine lol !I had issues with that when I snapped my tensioner. Tried going cheap but bought laser bmw sump tool especially, glad I did it needed about 200nm to crack it off -
@kds - still not found end of that spanner, it’s in engine bay somewhere?
- Posts
- 5,698
- Location
- North Manchester
Had a spare hour so decided to change the front nearside pads, should have smelt a rat when I noticed all the others had already been done.
Looks like someone had undone the bottom caliper bolt about 3mm before it got stuck so they just left it. 1 snapped bolt and 6 hours later I now have new pads fitted.
Next job is the outer cv boot, looks like they put a new one on then split it when they did the brakes and ball joint so there was grease everywhere.
Looks like someone had undone the bottom caliper bolt about 3mm before it got stuck so they just left it. 1 snapped bolt and 6 hours later I now have new pads fitted.
Next job is the outer cv boot, looks like they put a new one on then split it when they did the brakes and ball joint so there was grease everywhere.
Mukiwa
Well-Known Member
- Posts
- 469
- Location
- Winsford, Cheshire, near Oulton Park
Today I dropped the oil and flushed it out with fresh and a ‘cleaning agent’. Jacked two front wheels up to try tip as much as possible out of the rad. I’ve left it overnight with a pan underneath see how much drips out slowly.
This made it possible to locate my worn CV joint on the shafts. I’ve had problems identifying what it was in the past but with both wheels up and my head near the sump it was literally right in front of me.
View attachment 177737
Haven’t got a (15mm?) spanner to get access to the bolts as they are really tight. So I’ve opted to take it off at the joint for now so I can crack them off easily. I got all four wheels up before I worked out the handbrake was holding it
Surprised how the clips came out with just a bit of wiggling, suppose this is what it’s like when you actually have the right tool for the job
View attachment 177738 View attachment 177739
The adventure continues tomorrow when I go hunting for new CV and try to put oil back in without something going catastrophically wrong as usual
Wish me luck
Good luck! This is a job on my "to do" list!
- Posts
- 18,963
- Location
- Buckinghamshire, UK. ('95 DT)
Today I dropped the oil and flushed it out with fresh and a ‘cleaning agent’. Jacked two front wheels up to try tip as much as possible out of the rad. I’ve left it overnight with a pan underneath see how much drips out slowly.
This made it possible to locate my worn CV joint on the shafts. I’ve had problems identifying what it was in the past but with both wheels up and my head near the sump it was literally right in front of me.
View attachment 177737
Haven’t got a (15mm?) spanner to get access to the bolts as they are really tight. So I’ve opted to take it off at the joint for now so I can crack them off easily. I got all four wheels up before I worked out the handbrake was holding it
Surprised how the clips came out with just a bit of wiggling, suppose this is what it’s like when you actually have the right tool for the job
View attachment 177738 View attachment 177739
The adventure continues tomorrow when I go hunting for new CV and try to put oil back in without something going catastrophically wrong as usual
Wish me luck
9/16". My Halfords socket fits or you can get a propshaft socket off the Bay cheap.
Unless someone replaced with Britpart in which case they might be metric 14mm.
The leading edge of my bonnet was rusty as fook, but luckily a garage near hear were breaking one in Oxford Blue, so I got that off them and had it blown over at a paint shop, just shy of 200 wangers and she looks lovely. Just need to buy the letters because it looks weird being blank.
Datatek
Well-Known Member
- Posts
- 43,956
- Location
- Near Poitiers SW France
that's Universal Joint not a Constant Velocity joint.Today I dropped the oil and flushed it out with fresh and a ‘cleaning agent’. Jacked two front wheels up to try tip as much as possible out of the rad. I’ve left it overnight with a pan underneath see how much drips out slowly.
This made it possible to locate my worn CV joint on the shafts. I’ve had problems identifying what it was in the past but with both wheels up and my head near the sump it was literally right in front of me.
View attachment 177737
Haven’t got a (15mm?) spanner to get access to the bolts as they are really tight. So I’ve opted to take it off at the joint for now so I can crack them off easily. I got all four wheels up before I worked out the handbrake was holding it
Surprised how the clips came out with just a bit of wiggling, suppose this is what it’s like when you actually have the right tool for the job
View attachment 177738 View attachment 177739
The adventure continues tomorrow when I go hunting for new CV and try to put oil back in without something going catastrophically wrong as usual
Wish me luck
- Posts
- 58,170
- Location
- Preston Lancs.
Fuel injection pump:
Took 6 hours to remove all the rubbish and go to Halfrauds for the 17mm sump tool to remove the tension pulley. Changed all the o rings, installed a viton on in the HP head and drinking a cider for a job well done. What a ****ty job.
Tomorrow as Mr Haynes once said "fitting is the reverse of removal". We'll see
Oh dear this could be the start of something big.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,263
- Location
- Trapped inside my head @ LZ asylum
What’s a viton?
Thank you, my snapon socket I found under my starter fits but the cheap adapter sheard off, metric doesn’t quite grip it however I’m hoping to be able to change it on there without taking shaft off as there’s no beams in the way
@Bix - I did same, then realised once I had it my vehicles not oxford blue
.....well it kinda is now Mukiwa
Well-Known Member
- Posts
- 469
- Location
- Winsford, Cheshire, near Oulton Park
What’s a viton?
Thank you, my snapon socket I found under my starter fits but the cheap adapter sheard off, metric doesn’t quite grip it however I’m hoping to be able to change it on there without taking shaft off as there’s no beams in the way
@Bix - I did same, then realised once I had it my vehicles not oxford blue
Sorry Viton seal - should last a lot longer. Apparently.
Today's saga is that the DTI kit - for P38's! Well it isn't quite. Comes with 2 needles inside. Sizes 2 big & 2 small. If the adapter tubes were slightly longer then said long needle wouldn't be too big - it would fit. What this means is that if I try to push the DTI into the tube to seat properly it won't go in because 2 long needle is too long, by about 5 mm but could be a bit longer. Angle grinder time....
Mukiwa
Well-Known Member
- Posts
- 469
- Location
- Winsford, Cheshire, near Oulton Park
and I need to be in Truro for 9am tomorrow...........
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
Unlucky. You will struggle to find somewhere to park a Range Rover in Truro as well. Traffic is horrendous.
