welding exhaust manifold!!!!!!!

A

andy

Guest

• Jun 27, 2005

• #1

HIYA,

ive got a manifold off a turbo engine that has a crack about half way
round it, a mate said i could just mig it up, but im not sure,

whats the correct line on this, can i weld it or is it a specialist
job.

many thanks


andy

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com

 

L

LEE ARGYLE

Guest

• Jun 27, 2005

• #2

You can mig the manifold - but it's not recommended.
Your supposed to use special ARC rods that are designed for use with cast
metals - not cheap but worth the expense.

Regards


Lee
"andy" <[email protected]> wrote in message
news:[email protected]...
> HIYA,
>
> ive got a manifold off a turbo engine that has a crack about half way
> round it, a mate said i could just mig it up, but im not sure,
>
> whats the correct line on this, can i weld it or is it a specialist
> job.
>
> many thanks
>
>
> andy
>
> Posted Via Usenet.com Premium Usenet Newsgroup Services
> ----------------------------------------------------------
> ** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
> ----------------------------------------------------------
> http://www.usenet.com

 

A

Austin Shackles

Guest

• Jun 27, 2005

• #3

On or around Mon, 27 Jun 2005 17:37:40 +0000 (UTC), "LEE ARGYLE"
<[email protected]> enlightened us thusly:

>You can mig the manifold - but it's not recommended.
>Your supposed to use special ARC rods that are designed for use with cast
>metals - not cheap but worth the expense.

assuming it's cast... mig with normal wire and gas on cast don't work.

you should be able to bronze weld it with gas, mind, I think, although it
might not be strong enough.

other than that, like the man said, special cast-welding rods and the
know-how to use 'em.

--
Austin Shackles. www.ddol-las.fsnet.co.uk my opinions are just that
"Quos deus vult perdere, prius dementat" Euripedes, quoted in
Boswell's "Johnson".

 

S

Steve Taylor

Guest

• Jun 27, 2005

• #4

Austin Shackles wrote:

> other than that, like the man said, special cast-welding rods and the
> know-how to use 'em.

Pure nickel rods can be used on Cast iron. It is a stick (MMA) process,
and you should heat the job up very hot (>>300 C) while doing it. Once
finished, bury it in hot dry sand and let it cool.


Steve

 

T

Tom Woods

Guest

• Jun 28, 2005

• #5

On Mon, 27 Jun 2005 18:15:04 +0100, andy <[email protected]> wrote:

>HIYA,
>
> ive got a manifold off a turbo engine that has a crack about half way
>round it, a mate said i could just mig it up, but im not sure,

I think that you could mig it, but i'm told that the weld will
probably just fall off as soon as it gets warm or you knock it too
hard.

>whats the correct line on this, can i weld it or is it a specialist
>job.

I think it's a take it to a professional job, and if they dont do it
properly expect it to crack again.

 

A

Austin Shackles

Guest

• Jun 28, 2005

• #6

On or around Tue, 28 Jun 2005 20:48:47 +0100, Tom Woods
<[email protected]> enlightened us thusly:

>I think that you could mig it, but i'm told that the weld will
>probably just fall off as soon as it gets warm or you knock it too
>hard.

That's what happened to a part from my lathe, when I tried mig on it just on
the offchance that it'd work
--
Austin Shackles. www.ddol-las.fsnet.co.uk my opinions are just that
"Quos deus vult perdere, prius dementat" Euripedes, quoted in
Boswell's "Johnson".

 

T

Tom Woods

Guest

• Jun 28, 2005

• #7

On Tue, 28 Jun 2005 21:28:16 +0100, Austin Shackles
<[email protected]> wrote:

>On or around Tue, 28 Jun 2005 20:48:47 +0100, Tom Woods
><[email protected]> enlightened us thusly:
>
>>I think that you could mig it, but i'm told that the weld will
>>probably just fall off as soon as it gets warm or you knock it too
>>hard.
>
>That's what happened to a part from my lathe, when I tried mig on it just on
>the offchance that it'd work

I'd been tempted to try it too until i was told this! Nice to hear
that its actually correct!

 

A

Austin Shackles

Guest

• Jun 29, 2005

• #8

On or around Tue, 28 Jun 2005 21:58:43 +0100, Tom Woods
<[email protected]> enlightened us thusly:

>On Tue, 28 Jun 2005 21:28:16 +0100, Austin Shackles
><[email protected]> wrote:
>
>>On or around Tue, 28 Jun 2005 20:48:47 +0100, Tom Woods
>><[email protected]> enlightened us thusly:
>>
>>>I think that you could mig it, but i'm told that the weld will
>>>probably just fall off as soon as it gets warm or you knock it too
>>>hard.
>>
>>That's what happened to a part from my lathe, when I tried mig on it just on
>>the offchance that it'd work
>
>I'd been tempted to try it too until i was told this! Nice to hear
>that its actually correct!

Must try bronze on it - ISTR that this is possible. it's also a good deal
less hot than steel/iron welding.

--
Austin Shackles. www.ddol-las.fsnet.co.uk my opinions are just that
"Quos deus vult perdere, prius dementat" Euripedes, quoted in
Boswell's "Johnson".

 

G

Gaza

Guest

• Jun 29, 2005

• #9

Depending on where you are (and if you're the Andy i think you are,
you're not far - i'm in Sheffield) i could have a go at TIG welding it
for you. i have had some sucsess with cast in the past using stainless
rod as this removes some of the high carbon boundry layer that makes
them re crack. No guarentees but worth a go?

cheers

Gary

andy wrote:
> HIYA,
>
> ive got a manifold off a turbo engine that has a crack about half way
> round it, a mate said i could just mig it up, but im not sure,
>
> whats the correct line on this, can i weld it or is it a specialist
> job.
>
> many thanks
>
>
> andy
>
> Posted Via Usenet.com Premium Usenet Newsgroup Services
> ----------------------------------------------------------
> ** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
> ----------------------------------------------------------
> http://www.usenet.com