Strip down and rebuild into the ultimate Overlander.
- Thread starter landy-lee
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 9,018
- Location
- North Lincs
The bottom hinge is on upside down.....
- Posts
- 11,561
- Location
- Far out West
There’s a yellow plastic tub and a whole heap of nuts, bolts and washers on the near side wing?
- Posts
- 11,561
- Location
- Far out West
And a lolly stick under the wiper
v8250
Well-Known Member
- Posts
- 6,386
- Location
- Deepest Darkest...
I see the following:
- some bugger's super glued a yellow M6 fastener tub to your snow air intake
- you need to pick up those cable ties
- hope the Landy can in fact exit the garage - the Landy roof is VERY close to the garage ceiling
- the centre windscreen washer will hit the rail enabling screenwash to pour in [clean] the air vents and behind dash electrics
- oh, the windscreen bulkhead bolts...does this mean a fold down windscreen...?
- Posts
- 11,561
- Location
- Far out West
Also appears to be a ratchet strap attached to the roof inside the ve-hicle
I don’t know how to spell it !! That noise when you form a ring with your thumb and forefinger and sook through itWell I like it
+1 on the hinge. Half pint will do me.
v8250
Well-Known Member
- Posts
- 6,386
- Location
- Deepest Darkest...
This +1 , actually it's the right hand door lower hinge mounted to the left hand door lower hinge point
- Posts
- 11,020
- Location
- North of the Wall
You can't jack it up
- Posts
- 11,020
- Location
- North of the Wall
Is one of those mine for realising it was very close to the roof
If so, I'll have a pint of Punk IPA Its at the bar for you know!Is one of those mine for realising it was very close to the roof
- Posts
- 11,020
- Location
- North of the Wall
Aup lads
It been a wile but the Landy is about done!
Took a bit longer than i wanted but work have been crazy as i work for a company that makes LFT here in the uk.
On issue i have had when working on the Landy the past few months is that i struggle to take photos and now my garage is full with the Landy and not much too, to work.
On Wednesday i will be taking the boy out of the garage and parking it up on the drive!!
Photos will follow
Cheers Landy Lee
It been a wile but the Landy is about done!
Took a bit longer than i wanted but work have been crazy as i work for a company that makes LFT here in the uk.
On issue i have had when working on the Landy the past few months is that i struggle to take photos and now my garage is full with the Landy and not much too, to work.
On Wednesday i will be taking the boy out of the garage and parking it up on the drive!!
Photos will follow
Cheers Landy Lee
Hi all
So 346 days after getting my galvanised chassis the Landy is out!
The clutch is bit high so i think i need to adjust the master cylinder and the brakes are a bit spongy so will need to re bleed them
Still got the doors to do but now the Landy is out of the garage i have the room to now do all new galvanised doors. The old ones will stay on and i will swap one at a time.
First one is the rear door and my next job is to fit the DC-DC MPPT charger and Leisure battery for the fridge.
So 346 days after getting my galvanised chassis the Landy is out!
The clutch is bit high so i think i need to adjust the master cylinder and the brakes are a bit spongy so will need to re bleed them
Still got the doors to do but now the Landy is out of the garage i have the room to now do all new galvanised doors. The old ones will stay on and i will swap one at a time.
First one is the rear door and my next job is to fit the DC-DC MPPT charger and Leisure battery for the fridge.
