Classic Rear tailgate glass.
- Thread starter locket
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
The last one I claimed for,many years ago was the complete tailgate.unscrewed from the hinges. Auto glass said the frames where usually rusted so quicker to replace the lot.I inadvertently backed into a tree
With the tailgate open. They were charging the insurance over £750 my excess was £70 .
norseman
Well-Known Member
- Posts
- 3,278
- Location
- Essex - UK
The last one I claimed for,many years ago was the complete tailgate.unscrewed from the hinges. Auto glass said the frames where usually rusted so quicker to replace the lot.I inadvertently backed into a tree
Not your fault, silly place to leave a tree
Bit late, but safer to close the top tailgate by pressing on the lower corners not the centre handle esp if you have an ally framed one.
They can bow slightly in the centre which makes them harder to close.
Latch mechanisms benefit from periodical clean & lube - I do mine with a good blast of Plus-gas
They can bow slightly in the centre which makes them harder to close.
Latch mechanisms benefit from periodical clean & lube - I do mine with a good blast of Plus-gas
Well, this is interesting. I have contacted 5 glass company's and none of them have ever replaced the tailgate glass on a Classic and don't know how to.
I contacted my insurers and they have told me to buy a complete tailgate and either have it fitted by a reputable company or I can fit it and they will knock off £100 from my excess of £200.
I contacted my insurers and they have told me to buy a complete tailgate and either have it fitted by a reputable company or I can fit it and they will knock off £100 from my excess of £200.
Hicap phill
Well-Known Member
- Posts
- 16,337
- Location
- Wiltshire
Ask local car glazer to cut it to a pattern.
Autowindscreens done this for tractors/race cars and theses are BS marked
Autowindscreens done this for tractors/race cars and theses are BS marked
Hicap phill
Well-Known Member
- Posts
- 16,337
- Location
- Wiltshire
Give this chap a phone call.
https://www.heatedwindscreen.com/acatalog/land-rover-heated-windscreens.html
https://www.heatedwindscreen.com/acatalog/land-rover-heated-windscreens.html
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
4 big Phillips screws hold the hinges on and a couple hold the handle assembly I think the side locking mechanisms come with the frame.
What condition is the frame in?
Long time ago but I replaced the rotten frame on mine with the Famous Four ally kit. Still fine, so happy to suggest them.
Might be an idea to have a look at their website, they list the upper one with ally frame fitted with various glass types. You would need to transfer various bits from your old one.
http://www.rangerovertailgates.com/upper_tailgates
Long time ago but I replaced the rotten frame on mine with the Famous Four ally kit. Still fine, so happy to suggest them.
Might be an idea to have a look at their website, they list the upper one with ally frame fitted with various glass types. You would need to transfer various bits from your old one.
http://www.rangerovertailgates.com/upper_tailgates
mikieman
Well-Known Member
- Posts
- 332
- Location
- United States
A while ago... I changed my back hatch
Got three of the screws to break loose..
The last would not give ... got creative and really bogered up ... then I found it only has a long bolt and nut that hold on the henges
For me much easier to deal with ..,
Got three of the screws to break loose..
The last would not give ... got creative and really bogered up ... then I found it only has a long bolt and nut that hold on the henges
For me much easier to deal with ..,
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Yup, long bolt holds the top of the hinge to the body, couldn't you just drill off the fourth screwhead? Saves trying to realign the hinges.
mikieman
Well-Known Member
- Posts
- 332
- Location
- United States
Yes I suppose I could have drilled it out...
But my solution at that time was to dremel
It into a flat head...
I had gotten another hatch at the junk yard that was in much better shape... and at the junk yard this hatch unscrewed very easily
From the hinges... it wasn’t till I was installing it I discovered I had made a huge mistake... the learning curve kinda thing...
So when I say a while ago . It was a long
While ago...
discool
Well-Known Member
- Posts
- 13,628
I’m supprised that tailgates are still available.
https://rimmerbros.com/Item--i-RA1423ASSY
My 1987 3.5 started pealing after seven years as it was voted in a plastic style of paint and soon got worse, painting the pealing areas with Hammerite didn’t look good so I went out purchase a new replacement and found one a a local independent parts supplier that had just opened in my area it was the main dealer normally.
So I got a new genuine parts tailgate complete with heated glass, with the element pattern of the newer RRC of early 1990s, all for £82.00.
A direct swap fitted in 30 minutes of which 20mins was having fun readjust the latch rods so it tailgate identically locked on both sides.
Those were the days
https://rimmerbros.com/Item--i-RA1423ASSY
My 1987 3.5 started pealing after seven years as it was voted in a plastic style of paint and soon got worse, painting the pealing areas with Hammerite didn’t look good so I went out purchase a new replacement and found one a a local independent parts supplier that had just opened in my area it was the main dealer normally.
So I got a new genuine parts tailgate complete with heated glass, with the element pattern of the newer RRC of early 1990s, all for £82.00.
A direct swap fitted in 30 minutes of which 20mins was having fun readjust the latch rods so it tailgate identically locked on both sides.
Those were the days
Attachments
norseman
Well-Known Member
- Posts
- 3,278
- Location
- Essex - UK
Mine is an '87 & the tailgate (flap) is still on it after eleven years of my ownership, no idea how much of the 21 years of previous ownership it had been in place.
Admittedly the flap has been refreshed a couple of times & repainted by my local body-shop, the last attention included removal of the rotten metal strip holding the big bottom rubber, lashings of rust-converter then sticking the original (still in good order) rubber in place with industrial bonding material. Now the LH bottom corner of the frame has lifting paint so here we go again !
nb. This particular rubber seal has been totally unobtainable, but I think FF are doing it now @ £148
