Rear inner wing floor replacement

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
T

Trig

New Member
Posts
13
Location
Kettering (ish)
Landy noob in need of a bit of help please.

Ive been looking to get the rear floor repair kit from MPS (floor, supports and inner rear wings) to sort out the slight corrosion problem that these Disco's tend to have.

Ive already taken the boot floor out of mine and seen what I need to do with the supports and the floor section, but I havent really investigated the sections that go around the wing.

How are these sections fixed to the wheel arch tubs? Are they bonded on or welded?
 
I'd imagine they're spot welded and smeared with horrible sticky stuff to make sure they're water tight. you're probably better off patching them though as they're not seen.
 
:rolleyes: I'm just starting to realise how much welding a landrover can need.

In that case, and assuming you can get hold of replacement pannels. If I were you I'd cut the old ones off, leaving the welded part behind so you've got a thicker bit to weld to, they'll sit slightly further out but I don't think it'll be obvious - finish off with a good thick coat of underseal inside the wheel arch and you'll be sorted.

In the past few days I've patched up both chassis rails, the boot floor, the nearside rear wheel arch and the offside sill. I've not looked at the front footwells yet or the nearside sill but I doubt I'm done to be honest.

Then I'm gonna change all the brakepipes because, except under the bonnet, they're rotten. then I'm on to looking at bushes and strip/clean/reassemble brakes and sort a couple of lights that are out - then I'll be crossing my fingers it passes!!

Is there any reason I cant take it with mud tyres on?
 
Haha 20mm odd of tread, fail that ****er:D

dunno about speed ratings, worked in mot places but never heard
anything about that, might be one of those things that usually obviously
doesn't need checking though.
 
Just to update this as when you search 'discovery rear inner wing floor' on google this is the second link.

The floor sections were spot welded on and then covered in seam sealer. I found the bedt way to remove the floor sections from around the wheel tub was to simply cut it, just a bit away from the bend in the sheet and then to grind that lip back so you should be left with nice clean and flat metal to butt your replacement panel up to.
 
Trig said:
I found the bedt way to remove the floor sections from around the wheel tub was to simply cut it, just a bit away from the bend in the sheet and then to grind that lip back so you should be left with nice clean and flat metal to butt your replacement panel up to.
Click to expand...

:nopics:

Would be grateful if you've got pics of how you did it as I've got to do mine too.

Thanks.
 
I managed to find the photos elsewhere. Make what you can of them, I didnt take them to document too much of the job, so they arent great to show what I needed to do.

You can see on some of them though the lip that runs round the bottom of the wheel tub, the wing floor sections kind of sit on this, so you do need to get close to the wheel tub.


a2244cc1.jpg


277d7568.jpg


00801799.jpg


1322465a.jpg



The part of the panel that runs front to back (under where the dickie seats bolt on), there is a few spots of weld along there. I just cut the old panel infront of the inner rear quarter and ground it back, which also gave me a handy spot for welding the new panel to. It did mean the new panel had to be slightly forced underneath the old bit.
 
You must log in or register to reply here.

Similar threads

dag019
Fitting YRM extended second row floor upstand
Replies
14
Views
812
dag019
dag019
S
Disco 1 Disco 1 Rust repair prep
2
Replies
20
Views
2K
sv_dOnut
S
Disco-Skipper
Disco 2 Rust Repair Quote Reasonable?
2 3
Replies
54
Views
7K
tilly2
T
A
Different rear wing length
Replies
2
Views
1K
Bobsticle
Bobsticle
Goc3k
Discovery 1 SOLD 1997 300TDI manual D1, Winchester
Replies
16
Views
4K
Goc3k
Goc3k
Back
Top