Disco 1 Rear crossmember mounts
- Thread starter DiscoLyle
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 23,050
- Location
- In the next Glen
Cut the rubber mount in half lol 
Where did you get the replacement mount as it looks a tad long, you could just cut & flatten out the flaps to suit.
Where did you get the replacement mount as it looks a tad long, you could just cut & flatten out the flaps to suit.
Cut the rubber mount in half lol
Where did you get the replacement mount as it looks a tad long, you could just cut & flatten out the flaps to suit.
Its from YRM. Has anybody else had experience fitting these repair mounts?
Please could some message there mounts for me. It would be a massive help!!
- Posts
- 23,050
- Location
- In the next Glen
Yrm are usually very good I can measure mine tomorrow unless someone can do it tonight for you??
Thank you very much.
Yeh everything I've had off them so far had been excellent.
If the mount is correct, I cant get my head around how the ones on the car now have been modified. Ano the crossmember can sag but how can steel disappear
- Posts
- 23,050
- Location
- In the next Glen
Cheers Mate15mm of rust lol il check mine for ye.
Haha i could understand if 15mm fell off but its 15mm Between the crossmember and the chassis mount haha
- Posts
- 23,050
- Location
- In the next Glen
How much welding have you done if youve had other parts of yrm ive just started chopping my sills off for box
section the last owners welding is shocking so chop chop
How much welding have you done if youve had other parts of yrm ive just started chopping my sills off for box
section the last owners welding is shocking so chop chop
How much welding have you done if youve had other parts of yrm ive just started chopping my sills off for box
section the last owners welding is shocking so chop chop
I'm doing the same thing at the moment. I've done one sill already, im doing the other side tomorrow. See picture below. I still need to spray it with stone chip.
For the sills I bought the sill body mounts, brace bracket, and bushes. For the Crossmember i bought the two mounts and bushes.
For the sills I bought the sill body mounts, brace bracket, and bushes. For the Crossmember i bought the two mounts and bushes.
- Posts
- 23,050
- Location
- In the next Glen
Hicap phill
Well-Known Member
- Posts
- 16,319
- Location
- Wiltshire
I have a fresh crossmember on mine that I can measure for you tomorrow. Is there any other signs of patching on that crossmember? I’m surprised your doing just the mounts as it gets eaten inside out.
Looks like your doing a nice job there!
In fact, looking at the pic, I’d sell your mounts on eBay and get the full think mate. You then know it’s all the right fit as one component.
Looks like your doing a nice job there!
In fact, looking at the pic, I’d sell your mounts on eBay and get the full think mate. You then know it’s all the right fit as one component.
Yeah let me know if any others you need. I didn’t even measure existing, you’ll honestly chase your tail patching up the crossmember. Are the boot and inner wings/arches dead too?
Cheers
I just finished repairing the boot floor and arches.
The tailgate is catching on the rear bumper. Im hoping that its just the hinges. However it has ruined the tailgate. So I'm looking for a complete tailgate and hinges in 601 paint code.
I have a rioja one here going scrap as hinges aren’t great and dent in the top. I went to a breaker and he said just take the whole thing rather than just hinges. He had another rioja too that he was breaking (Other end of country from you though).
