Datatek
Well-Known Member
- Posts
- 43,918
- Location
- Near Poitiers SW France
Nice.
Rare p38?
- Thread starter Dandor1986
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 58,170
- Location
- Preston Lancs.
They would have a job to remove mine, the bolts are rusted solid into the swan neck.
There are no bolts attaching mine it slides in and is held by a catch. Stores in tool tray in boot when not in use.
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
Dandor, which are planning on doing first.. your Range Rover or your grass ?
welcome
welcome
kds
Well-Known Member
- Posts
- 2,217
- Location
- old,ugly, tired in Lincoln.
He might have cut it by now, feb 2016 picture.Dandor, which are planning on doing first.. your Range Rover or your grass ?
welcome
- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
They would have a job to remove mine, the bolts are rusted solid into the swan neck.
I think ours are different mate. What you are describing is like mine with some large through bolts holding it in place. Think I can see a catch on the right side wammers is on about
- Posts
- 58,170
- Location
- Preston Lancs.
Look at RAVE accessory fitting instructions for STC8939 detachable tow bar. That is the same as mine. It is just unclipped a cover fitted, and swan neck is then stored in boot accessory tray. That is the expensive tow bar. The one with the bolt through it is the poverty model. The photos supplied by Dandor 1986 does have the QD bar fitted that is why i advised him to remove and stow it.
- Posts
- 58,170
- Location
- Preston Lancs.
yep. Poverty spec here
A lot less likely to be nicked though. The QD ones are out of production as far as i am aware, they are as rare as hens teeth to find a replacement for if lifted, they only take a few seconds to remove.
May I be impertinent and ask,
How cheap is cheap?
True. Don't think anyone is going to nick mine although I do enjoy that there is less to go wrong. Must get a new tow hitch cover as mine was pinched thoughA lot less likely to be nicked though. The QD ones are out of production as far as i am aware, they are as rare as hens teeth to find a replacement for if lifted, they only take a few seconds to remove.
Yep that's it
gold rover
Well-Known Member
- Posts
- 10,132
- Location
- Scotland,
I think you'll be hard pressed to get a reply. Someone woke a thread that had been in deep sleep, for two and a half years. The OP hasn't been seen since he was told his vehicle wasn't rare or special.
gold rover
Well-Known Member
- Posts
- 10,132
- Location
- Scotland,
Registered Feb 2000, so may have sat unregistered for a while, so 1999 build? Would that possibly explain tail lights? I know I've had crossover models on other marques and some bits were previous model, some were the latest.
- Posts
- 2,427
- Location
- Isle Sheppy
Mine was registered 2000 but parts are 1999
Henry_b
Think outside, no box required.
- Posts
- 15,353
- Location
- somewhere else
Doesn't look anything special about that to be honest. Remove the detachable tow bar and put it in the boot before before some tea leaf has it away, they are hard to find.
I removed mine to stop me whacking my shin on it!!
Fookin thing..
- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
Tanis' fault!
gold rover
Well-Known Member
- Posts
- 10,132
- Location
- Scotland,
He's a very naughty boy
