Please help

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
O

Old diver

Well-Known Member
Posts
432
Location
Dunfermline, Fife
2006 Freelander 1 TD4. Put on new drums, all new brake pads etc. New handbrake cables. Tried to adjust handbrake and run out of adjustment, no handbrake at all. Pumped foot brake 30 times before trying to adjust anything. I'm at a loss with this damn vehicle. Any suggestions please.
 
There's an adjuster within the drum set up on the back, you need to set that first before adjusting the handbrake. The way I did it was a little trial and error but did the job. Take the drum off and adjust the ratchet with a screwdriver, keep trying the drum on as you do it. You'll get to a point where you feel the shoes against the drum as you put it on, you want resistance but not to make it impossible to get the drum back on. I don't think the autoadjustment works without some initial pressure. Do this both sides and I'd also slacken off the handbrake adjuster before you do it. Hope this helps!
 
Conners said:
There's an adjuster within the drum set up on the back, you need to set that first before adjusting the handbrake. The way I did it was a little trial and error but did the job. Take the drum off and adjust the ratchet with a screwdriver, keep trying the drum on as you do it. You'll get to a point where you feel the shoes against the drum as you put it on, you want resistance but not to make it impossible to get the drum back on. I don't think the autoadjustment works without some initial pressure. Do this both sides and I'd also slacken off the handbrake adjuster before you do it. Hope this helps!
Click to expand...
Thanks for that, I thought that was the reason for pumping the 30 times to adjust the pads closer. I will give that a go tomorrow, thanks again.
 
I hope this isn't sucking eggs and all that - but are you sure everything went back on the way it came off? I took advice from here and took pictures before I stripped everything down so that I could make sure it went back correctly. I didn't replace the cables, but I did replace drums and everything inside them, and it all just went back together and worked perfectly.

This was on the earlier setup on a '99 car and luckily everything was set up correctly before I took the drums off!
 
When refitting the shoes back off the handbrake adjuster nut to the end of its thread. At this point the shoe adjuster should be pre-adjusted so the drums just slide on. Now you need to turn the adjuster manually through the inspection hole on the rear of the drum backplate, once the rubber bung is removed. Click the adjuster over until the drum begins to drag. Then pump the foot brake a dozen times, with the engine running.

Re-check for drum drag and back off the adjuster if excessive. At this point adjust the HB cables to give the correct lever movement.
 
GrumpyGel said:
I hope this isn't sucking eggs and all that - but are you sure everything went back on the way it came off? I took advice from here and took pictures before I stripped everything down so that I could make sure it went back correctly. I didn't replace the cables, but I did replace drums and everything inside them, and it all just went back together and worked perfectly.

This was on the earlier setup on a '99 car and luckily everything was set up correctly before I took the drums off!
Click to expand...
I took pics with the iPad so I would know it went back correctly.
 
Old diver said:
I took pics with the iPad so I would know it went back correctly.
Click to expand...

This is a correctly assembled off side rear shoe assembly.
20180325_131517.jpg
 
When replacing shoes I normally use a sanding disc on a grinder to take the lip off the hub, then adjust the shoes until I can just about slide the hub on but it can still turn freely.
Don't assume that because you put them back on the same as they were before that they are on correctly. Many on here caught out that way before. Double check they are correct according to Nodges pic.;)
 
Alibro said:
When replacing shoes I normally use a sanding disc on a grinder to take the lip off the hub, then adjust the shoes until I can just about slide the hub on but it can still turn freely.
Don't assume that because you put them back on the same as they were before that they are on correctly. Many on here caught out that way before. Double check they are correct according to Nodges pic.;)
Click to expand...
I put on brand new hubs so no lip. For some reason the auto adjust didn't work, the cog needed winding on a bit. I adjusted the pads till they were just rubbing then adjusted the handbrake cables. I now have a handbrake that is working but I am not 100 % happy with it. I will give it a few days, then do it again. I always take pics with the IPad before stripping anything down.
 
Old diver said:
I put on brand new hubs so no lip. For some reason the auto adjust didn't work, the cog needed winding on a bit. I adjusted the pads till they were just rubbing then adjusted the handbrake cables. I now have a handbrake that is working but I am not 100 % happy with it. I will give it a few days, then do it again. I always take pics with the IPad before stripping anything down.
Click to expand...
Many thanks to all who advised on my problem.
 
What's the handbrake travel like? Also when it is off do you have a bit of slack in the cable?
 
You must log in or register to reply here.

Similar threads

damian46
Rear drum brake adjuster
Replies
1
Views
520
damian46
damian46
L
Hand brake question
Replies
14
Views
637
romanrob
R
B
Sport EPB issue over temp issue
Replies
0
Views
377
bigsmithy
B
J
Freelander 1 Rear Drums strip and rebuild
Replies
6
Views
877
Jimbo70
J
P
freelander 1 td4 alarm keeps going off
Replies
15
Views
1K
peter house
P
Back
Top