I would just like to say

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Hippo said:
From wot eye remember from the pic's it dun't look like much wuk for a plasterer. Not many big area's. Lots of edges wiv door frames and walls. A plasterer could have that done in 2 days easily if they had a van full of bits from wix.
Click to expand...
Young lad turned up 10.15am saying he's supposed to do 10 square metres, that'll be the ceiling and one wall in my estimation, I'll see how he gets on :)
 
Hippo said:
Fink e's in Kernow so cornishwallcestershire.
Click to expand...
Think he's back on here. noticed his style yet again. Think he is now calling himself "Tax Dodgers".
See what you think.
www.landyzone.co.uk

Discovery 2 maf delete

Hi all I do a fair bit of green leaning and keep getting maf sensor wet which is getting to be a pain how do I go about removing it I know it needs mapping out but what mechanical changes need to be made Thanks
www.landyzone.co.uk www.landyzone.co.uk
 
Stanleysteamer said:
Think he's back on here. noticed his style yet again. Think he is now calling himself "Tax Dodgers".
See what you think.
www.landyzone.co.uk

Discovery 2 maf delete

Hi all I do a fair bit of green leaning and keep getting maf sensor wet which is getting to be a pain how do I go about removing it I know it needs mapping out but what mechanical changes need to be made Thanks
www.landyzone.co.uk www.landyzone.co.uk
Click to expand...
Banned last week.
 
Hippo said:
Contract was supply and support. Fujitsu would have always had access.
Click to expand...
That much is obvious, but wasn't obvious is how much they, together with the PO abused this. Until all this came out.
AND once they realised the Horizon system was faulty, they tried to cover it up and stick Bandaids over stuff rather than close it down, rewrite the bits that needed doing and then TEST it properly.
Sadly, so often the case.
 
Stanleysteamer said:
If that was him, then he really makes no effort to cover up his style.
Perhaps he does it on purpose and keeps trying to improve on his "personal best " time! 🤣 🤣 🤣
Click to expand...
Fink he's getting a kick out ovvit. Years ago some peeps came on ere to visit AG then take the mick int tech sections. Comments like 'dun't bother fixing the brakes. HGF before the month is oot'. Tech sections were ruffer back then. We had 3 active mods to keep us inline. And sometimes mod1 would crawl oot from under his bridge. Fink bob see's the place as being the same as back then. Posts in the style of how it was before years ago.
 
Stanleysteamer said:
Think he's back on here. noticed his style yet again. Think he is now calling himself "Tax Dodgers".
See what you think.
www.landyzone.co.uk

Discovery 2 maf delete

Hi all I do a fair bit of green leaning and keep getting maf sensor wet which is getting to be a pain how do I go about removing it I know it needs mapping out but what mechanical changes need to be made Thanks
www.landyzone.co.uk www.landyzone.co.uk
Click to expand...
👌👌👌
 
Makeing bread to day to cold and windey out side as I found when digging up carrots
17047184556761463238864.jpg
 
You must log in or register to reply here.

Similar threads

L
Learning to fix Land Rovers like a pro - career advice wanted
Replies
10
Views
794
kevstar
kevstar
K
What money should I be asking?
2
Replies
20
Views
919
Atomician
Atomician
Lackingsense
Sport Air suspension/HDC fault
Replies
14
Views
1K
Lackingsense
Lackingsense
J
300 Tdi engine swap story - and a few questions
Replies
13
Views
1K
doriz
doriz
J
300 Tdi Engine back in, nearly - Story and at the end Questions
Replies
0
Views
541
jer_300Tdi_90
J
Back
Top