robint
Well-Known Member
- Posts
- 7,057
do i need to take my gearbox out to remove the tranfer box 
i need help quick !!
- Thread starter robint
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
I removed the entire body on my disco so I could remove the transfer box. I reckon you'll need to do the same.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
I is gotta remove the engine from a disco tomorrow should I leave the gearbox attached to the engine and take it all out in one piece?
robint
Well-Known Member
- Posts
- 7,057
Sirus
Your all Banned except me
- Posts
- 22,196
- Location
- The Country of Black
I removed the entire body on my 90 so I could remove the transfer box. I reckon you'll need to do the same.
Thats bollox, you just put it on its side
just done a 12 page hse risk assessment and due to the prevailing wind conditions will need to completely strip and catalogue it. Also forwarded body flight plan so as not to interrupt sleaze jet or Mary poppins
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Don't be daft ya can't do that.. Yu need 4 lads to turn the house for ya while yu hold the bulb. If ya try to do it all ya self you'll break the bulb.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
robint
Well-Known Member
- Posts
- 7,057
Yu int been listening to SChitt0464 have yu
he knows best hes a trained machanic ant he
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Thats bollox, you just put it on its side
sssssshhhhhh FFS
am trying to sell that fooker. tis light greenlaning damage not a rollover ffs..
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Trewey
Cockernee, Pasty munchin bastid.
- Posts
- 20,088
- Location
- Kernow - Near England
Removing Transfer Box, without removing Gearbox.
Relatively simple job, but you need strong arms if you on your own. Remove both floor panels, trans tunnel and centre seat box cover. Remove front and rear props from transfer box, hand brake assembly and PTO cover support bearing and the gear assembly (makes reassembly much easier). Disconnect breather pipes and dif Hi/Lo rods. Undo the bolts that hold transfer box to main box and slide it back off the input shaft.
get some long (200mm ish) M10 bolts - cut the heads off and put a slot in the end (for a screwdriver) - undo the tranny box bolts and replace them one by one with the long bolts - when all are replaced slide the tranny box away from the GB, once the shaft has cleared lower the tranny onto yer skateboard
don't forget to have plenty for breakfast before you start
Relatively simple job, but you need strong arms if you on your own. Remove both floor panels, trans tunnel and centre seat box cover. Remove front and rear props from transfer box, hand brake assembly and PTO cover support bearing and the gear assembly (makes reassembly much easier). Disconnect breather pipes and dif Hi/Lo rods. Undo the bolts that hold transfer box to main box and slide it back off the input shaft.
get some long (200mm ish) M10 bolts - cut the heads off and put a slot in the end (for a screwdriver) - undo the tranny box bolts and replace them one by one with the long bolts - when all are replaced slide the tranny box away from the GB, once the shaft has cleared lower the tranny onto yer skateboard
don't forget to have plenty for breakfast before you start
