jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
Ah I thought your old engine had the pump turned up and timing really out
Hertfordshire Lanes?????
- Thread starter 99claydond
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Demonbiker
Active Member
- Posts
- 142
- Location
- Stevenage
Pump is turned up,a little, never used to smoke,app timing was set 6 degrees advanced, ran fine even on oil, wondering if guy who set it has got it right or retarded a bit?? He did use the rocker gear from other head and reset the valve clearances, again wonder if too tight?
Gets a bit of white smoke at startup, takes 4-5 turns to catch, bit missy , rev it and clears then fine
Gets a bit of white smoke at startup, takes 4-5 turns to catch, bit missy , rev it and clears then fine
Shortandfluffy
New Member
- Posts
- 15
- Location
- Luton
You all look like you had a laugh, where was the circuit
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
My old mans disco takes a full revolution if not 2 to fire I believed 300's were more prone to this than the 1/4 turn of the key for a 200 as the 200
Gets max fuel on start and a puff of black smoke where 300 doesn't.
What were the bores like when you had the head off??
How hot did it get with a blocked rad??
Have you changed the pressure switch 4 vehicles all
Suffered from 20 year old switches and they all failed within a year of each other the diaphragm split after inspection giving a flickering light at tickover.
Can't really help much wasn't involved but if I can help I will.
J
Gets max fuel on start and a puff of black smoke where 300 doesn't.
What were the bores like when you had the head off??
How hot did it get with a blocked rad??
Have you changed the pressure switch 4 vehicles all
Suffered from 20 year old switches and they all failed within a year of each other the diaphragm split after inspection giving a flickering light at tickover.
Can't really help much wasn't involved but if I can help I will.
J
Demonbiker
Active Member
- Posts
- 142
- Location
- Stevenage
Doesn't puff black smoke, bore looked honed when head off and bottom end looked clean when sump changed, has new oil switch fitted and a gauge on dash, got to about 3/4 on temp gauge , 100ish on other gauge before rad changed, now runs bang in middle of both gauges
Light only flickers at idle after a run at 60-70 ish, even after changing oil
Light only flickers at idle after a run at 60-70 ish, even after changing oil
wilob
Active Member
- Posts
- 252
- Location
- Nr. Bodmin. Cornwall
m4drx
Active Member
- Posts
- 194
- Location
- Bedfordshire
anyone know when the next roundhill woods day is?
Who's planning to go?
Who's planning to go?
Piperpa27
New Member
- Posts
- 43
- Location
- Watford, Herts
It's running 15th and 16th March (Roundhill Woods)
m4drx
Active Member
- Posts
- 194
- Location
- Bedfordshire
thought it was end of feb. Bit of a wait then. I really enjoyed the last one. Any other events going on? or just Whaddon and the swear word that is Devils Pit?
I really enjoyed the last one. Any other events going on? or just Whaddon and the swear word that is Devils Pit?
Yarwell is a good site, but it's a slap up to the other side of Peterborough.
You're lucky you can go anywhere, I'm just sitting looking at mine broken, but it will return in a magnificent state with a V8
Farrar
Well-Known Member
- Posts
- 1,007
- Location
- Bedfordshire
Yarwell is a good site, but it's a slap up to the other side of Peterborough.
You're lucky you can go anywhere, I'm just sitting looking at mine broken, but it will return in a magnificent state with a V8
No more water for you then!!!!!!
I'm going with Megasquirt ignition , so as waterproof as it gets, does away with the distributor.
I tend to avoid water now anyway, it kills diffs, alternators, starter motors, fans.
Just costs money every time.
Defenderdog1
Active Member
- Posts
- 404
- Location
- Hemel Hempstead
Spyderman where did you get your ground anchor from?
Titch1987
Active Member
- Posts
- 123
300tdistu off here makes them I got my light bars from him and there made really good going to get rock sliders off him soon aswell
Farrar
Well-Known Member
- Posts
- 1,007
- Location
- Bedfordshire
Do you know how much they are.
Titch1987
Active Member
- Posts
- 123
Fleabay, but it's a Devon 4x4 one. probably the best one out there, but it's big and pretty heavy, never let you down, super tough. http://www.devon4x4.com/index.php?p...ategory_id=67&option=com_virtuemart&Itemid=14
X-Eng make a good one, quite compact.
Don't get a crap one they're useless.
Last edited:
stutab
Well-Known Member
- Posts
- 3,285
- Location
- Hemel Hempstead, Hertfordshire
Sounds fun. You upgrading your braking system as well?
Looks OK ish, I wouldn't buy it though as it's a fixes head version, my blade detaches so much easier to store inside, plus it's lacking a ring at the blade end to get the thing out of the ground if it gets stuck.
Cheap though, depends on how much you think you might need it, places like Whaddon has given mine some serious use, as there aren't many trees to anchor from and anchoring to other motors just drags them along as well if the motor is really stuck.
Advice is buy the best you can afford, buy right, buy once.
Brakes are fine, as long as they're looked ager there's nothing wrong with Series brakes, especially as mine has the twin 11" drums on the front.
I'm going for power steering, because it's relatively easy and it'll stop the steering kicks off road and make it a lot easier at very low speeds.
