Hertfordshire Lanes?????

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
It looks like the bolt in question is #10 in the diagram. It appears that there is not a nut behind it. Yesterday I was able to tighten it in, but the non-threaded part still stuck out by about 1 or 2 cm, so not fully in.

I'll try and borrow some sockets to see if I can get it down more

Thanks,
 

Attachments

  • engine.jpg
    engine.jpg
    131.7 KB · Views: 155
Wiring Victory! After spending an hour with a multimeter, some electrical tape, a warm jumper and a head torch i have (touch wood) solved my wiring woes. Take that archaic, poorly designed wiring loom!
 
stutab said:
Is that one page done yet?
Click to expand...

haha not quite, it should be tomorrow though, i have a bunch of parts arriving and can hopefully get atleast most of them fitted. it is going to be a day full of learning when i get to do the drag link, trackrod end, front pads and swivel pins. that will be a fun day for sure. i have been doing some reading and am going to take a look at removing shims from the swivel pins, it seems logical to do them all at once.
 
Leebastard said:
haha not quite, it should be tomorrow though, i have a bunch of parts arriving and can hopefully get atleast most of them fitted. it is going to be a day full of learning when i get to do the drag link, trackrod end, front pads and swivel pins. that will be a fun day for sure. i have been doing some reading and am going to take a look at removing shims from the swivel pins, it seems logical to do them all at once.
Click to expand...

Good luck, not got to that with mine yet so dunno what it's like. Have fun
 
jai_landrover said:
https://www.facebook.com/events/245778945571707/?refid=18&ref=m_notif&notif_t=group_activity

I know Colin quite well!!

Myself an Rach took part in the first of these events run earlier this year! Good fun good cause and bloody funny when you get completely wrong answers!!

We ended up finding some greenlanes and having a laugh.

Good cause,
Good people,
Right laugh!!

ALL money gets sent to charity!

J
Click to expand...

Good cause, shame but I'm doing Roundhill Woods that day
 
Leebastard said:
haha not quite, it should be tomorrow though, i have a bunch of parts arriving and can hopefully get atleast most of them fitted. it is going to be a day full of learning when i get to do the drag link, trackrod end, front pads and swivel pins. that will be a fun day for sure. i have been doing some reading and am going to take a look at removing shims from the swivel pins, it seems logical to do them all at once.
Click to expand...

How's the Landy coming along?
 
Defenderdog1 said:
How's the Landy coming along?
Click to expand...

Electrics sorted, wiper mechanism rebuilt. Just the mechanical bits now, need to find the time is all. I'm hoping the swivel can be adjusted with the shims rather than new socket/ball. Apparently my tow bar electrics are a fail too I think I'm just going to cut the socket off and tape the wires up haha. I also need to remove my tow ball, as towing point without electrics is a fail.
 
Thought the MOT only checked the modern 13 pin electrics, its just a visual check for damage on the old 7 pin sockets, certainly never heard of it being a fail to have a towball with no electrics !

Yup a quick trawl shows that 7 pin electics is a visual check to say that the cable and sockets are secure, there is no functional check at all. e.g. if the socket is hanging by the cable then yes its a fail. however there is NO fail for having a towbar with NO elecrics.
 
Last edited:
You must log in or register to reply here.

Similar threads

A
Peak District lanes
Replies
8
Views
1K
Anaconda
A
A
Non Scratchy Greenlane Trip Berkshire/Wiltshire
Replies
10
Views
1K
Anaconda
A
T
Any Series Owners in the Phoenix Area?
Replies
9
Views
506
Bobsticle
Bobsticle
A
Greenlane trip 19th August
Replies
7
Views
2K
Anaconda
A
Shogun243
LLandrillo - Wayfarer
Replies
1
Views
899
300bhp/ton
300bhp/ton
Back
Top