- Posts
- 10,639
- Location
- Oxfordshire
how are you putting the epoxy on?
Here we go again, Project "Red shed"
- Thread starter aaronmorris
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Yeah I'll have the springs for the cadillac 
IamRobbie
Well-Known Member
- Posts
- 2,800
- Location
- Derbyshire, j28 M1
good point, i need a rear near side spring seat, paddocks it is for me
- Posts
- 14,902
- Location
- Doncaster
Yeah I'll have the springs for the cadillac
If you can wait until August for them, I can transport them to Blackpool for you, might help. The wife's just booked a holiday up there!!
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
If you can wait until August for them, I can transport them to Blackpool for you, might help. The wife's just booked a holiday up there!!
I'm in no rush
need to finish the chassis off first anyway I'll stick something in LZ courier anyway just incase someones coming up north sooner but if not I'll grab them off you in August
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
That is one big ass engine !
Its going to be a monster
Will be when it's finished.Spray gun for the most of it and used a brush a little bit in hard to reach areas.
You thinking of using it? 'tis good stuff
Yeah I'll have the springs for the cadillac
No worries, I'll not ebay 'em then, Hopefully sort some sort of delivery out, Although they're bloody long.
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
So todays jobs was mainly to do with the sump.
Basically the sump needs to be reversed so the dip stick needs moving and the oil pick up needs moving.
So sump off.
[/URL][/IMG]
Old pick up.
[/URL][/IMG]
Removed pick up pipe and chopped the end off.
[/URL][/IMG]
Now I had originally bought a length of rubber hose, But when I tried it their wasn't enough room for the bend and was kinking the pipe, Now I could have cut the flange (above) of and welded as 90 angle on it, But I've no gas for the welder.
So I had a hunt around and found this bit of pipe which has a 90degree bend on it all ready.
Hose was off the power steering reservoir for the daf 45. So that worked out well
[/URL][/IMG]
Pipe cut to length and jubilee clipped.
[/URL][/IMG]
Dip stick was knocked out from the sump side with a punch.
[/URL][/IMG]
Knocked a core plug out and refitted at the back of the engine. Will deal with dip stick length when I get some oil in it. Also need to put a new core plug in where the dipstick used to be. Need to find a supplier that'll sell me just 1.
[/URL][/IMG]
Sump was a mess to say the least.
[/URL][/IMG]
So gave It a clean with the wire wheel and painted it.
[/URL][/IMG]
And refitted.
[/URL][/IMG]
New swivel seal retainers arrived (I ordered the wrong ones)
So I build the swivel housings up on the bench.
[/URL][/IMG]
And fitted along with stub axles.
Hopefully get it fully built up tomorrow provided I can find the bits.
[/URL][/IMG]
Basically the sump needs to be reversed so the dip stick needs moving and the oil pick up needs moving.
So sump off.
Old pick up.
Removed pick up pipe and chopped the end off.
Now I had originally bought a length of rubber hose, But when I tried it their wasn't enough room for the bend and was kinking the pipe, Now I could have cut the flange (above) of and welded as 90 angle on it, But I've no gas for the welder.
So I had a hunt around and found this bit of pipe which has a 90degree bend on it all ready.
Hose was off the power steering reservoir for the daf 45. So that worked out well
Pipe cut to length and jubilee clipped.
Dip stick was knocked out from the sump side with a punch.
Knocked a core plug out and refitted at the back of the engine. Will deal with dip stick length when I get some oil in it. Also need to put a new core plug in where the dipstick used to be. Need to find a supplier that'll sell me just 1.
Sump was a mess to say the least.
So gave It a clean with the wire wheel and painted it.
And refitted.
New swivel seal retainers arrived (I ordered the wrong ones)
So I build the swivel housings up on the bench.
And fitted along with stub axles.
Hopefully get it fully built up tomorrow provided I can find the bits.
Last edited:
Stickystuff
Member
- Posts
- 34
We'll I read your blue 90 build page by page and I'm mega impressed!
I've just finished reading this thread and all I can say is WOW!
That's going to be a monster when it's running!
Will it still be a 4x4? Or just rear drive? If so how are you going to manage the transfer box?
Keep up the good work!
I've just finished reading this thread and all I can say is WOW!
That's going to be a monster when it's running!
Will it still be a 4x4? Or just rear drive? If so how are you going to manage the transfer box?
Keep up the good work!
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
Cheers for the kind comments
I hope it'll be a monster when it's up and running
It will still be 4x4. But need to have an adaptor shaft/plate made up to join the gearbox and lt230 together. Which went away to be done today
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
So today I haven't done a lot, But the thing that had been worrying me is now in hand.
Yep that would be the gearbox/transfer box adaptor.
It may take a while but it's in good hands and now I know I can get them joined together I will start removing the old engine and buying the bits I need.
I only didn't in case things went tits up.
Then the paint turned up this afternoon, So I painted my engine.
It's, Erm, A bit bright Should look better with some black bits
[/URL][/IMG]
[/URL][/IMG]
[/URL][/IMG]
[/URL][/IMG]
Yep that would be the gearbox/transfer box adaptor.
It may take a while but it's in good hands and now I know I can get them joined together I will start removing the old engine and buying the bits I need.
I only didn't in case things went tits up.
Then the paint turned up this afternoon, So I painted my engine.
It's, Erm, A bit bright
Should look better with some black bits
Bennehboy
Well-Known Member
- Posts
- 2,202
- Location
- Huddersfield
:d
sp00k
Well-Known Member
- Posts
- 1,530
- Location
- Washington, County Durham, UK
Engine looks good. Bus spec red - seems appropriate for an engine often found in buses
Beckito
Member
- Posts
- 30
- Location
- Knowsley Village, Liverpool
Cooking hell Aaron, I know I said the last one was dirty Everton Blue.......that is definitely Liverpool Red! Awesome. Brilliant thread as usual. Has that nosey ba5tard of a neighbour been sticking his oar in once the painting has started? Ooh the fumes are no good for my poor chest etc etc!
Beckito
Member
- Posts
- 30
- Location
- Knowsley Village, Liverpool
*fooking
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
I'll be grinning like that when it's running
Engine looks good. Bus spec red - seems appropriate for an engine often found in buses
Yep, I did contemplate blue but thought red was a suitably lairy colour for this engine
Cheers
This engine is going in the blue one now
Erm, Neighbour hasn't said anything recently, But when I painted the engine yesterday I threw a tarp up so they couldn't take pictures of me painting.
Don't want any evidence against me now do I
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
More engine painting today, Albeit not a lot.
First job was to paint the sump again as it got covered in red paint
Then cleaned the air intake plate up.
[/URL][/IMG]
Lick of paint
[/URL][/IMG]
Next job, Get all the old paint off the injector pipes.
What a bloody boring long drawn out job that was
[/URL][/IMG]
[/URL][/IMG]
Started cleaning the rocker pots up back to bare ali, Paint was all flaking off and looked a mess so was the only option.
Now I've got two thoughts at the moment, Paint them blue (body colour) OR polish them.
What yer recon?
[/URL][/IMG]
Painted and fitted a few bits to front of the engine.
[/URL][/IMG]
Injector pipes painted and fitted, Along with air intake plate.
[/URL][/IMG]
[/URL][/IMG]
[/URL][/IMG]
[/URL][/IMG]
Infact, I've just had a thought, Don't know why I'm putting all this in this thread when it's going in the blue one now :doh:
First job was to paint the sump again as it got covered in red paint
Then cleaned the air intake plate up.
Lick of paint
Next job, Get all the old paint off the injector pipes.
What a bloody boring long drawn out job that was
Started cleaning the rocker pots up back to bare ali, Paint was all flaking off and looked a mess so was the only option.
Now I've got two thoughts at the moment, Paint them blue (body colour) OR polish them.
What yer recon?
Painted and fitted a few bits to front of the engine.
Injector pipes painted and fitted, Along with air intake plate.
Infact, I've just had a thought, Don't know why I'm putting all this in this thread when it's going in the blue one now :doh:
IamRobbie
Well-Known Member
- Posts
- 2,800
- Location
- Derbyshire, j28 M1
Where did my post go?
Jam1
Well-Known Member
- Posts
- 1,315
- Location
- Staffordshire
Pots I reckon polished or black
wirral_series2a
Active Member
- Posts
- 140
- Location
- Wirral
Yep, leave polished ; gives the engine a certain 'aged' charm
Great thread btw :clap2: Keep it here until the engine is out of the blue one
Re neighbours, I have a defender and so does my young neighbour...he is very enthusiastic but also a tad noisy etc ( I can live with it but it has caused an amazing amount of anger:argue: from the neighbour opposite resulting in police called and now both sets have fitted cameras monitoring each other )
Great thread btw :clap2: Keep it here until the engine is out of the blue one
Re neighbours, I have a defender and so does my young neighbour...he is very enthusiastic but also a tad noisy etc ( I can live with it but it has caused an amazing amount of anger:argue: from the neighbour opposite resulting in police called and now both sets have fitted cameras monitoring each other
)
Landyfox
Well-Known Member
- Posts
- 4,489
You're MAD end of
