Tomjones12
Member
- Posts
- 30
- Location
- Wales
I've undone my injector and the main body has come out and the spring but the nozzle and end poce stuck on block any help would be great to get it out its on a 200 tdi
Help needed with injector nozzle stuck in block
- Thread starter Tomjones12
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
freelance
Well-Known Member
- Posts
- 8,486
- Location
- essex and beyond
Can you screw main body back into nozzle, and keep turning clockwise?
Tomjones12
Member
- Posts
- 30
- Location
- Wales
Thread broken
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
You might be able to drill into it, and screw in a self tapper, and use a slide hammer or other instrument.
If that doesn't work, take the head off and try and drift it out from inside.
I am reporting your thread, and it will get moved to a better section later.
Tomjones12
Member
- Posts
- 30
- Location
- Wales
I'm grearfull for help I did think of using a bolt extractor and unscrew it
Tomjones12
Member
- Posts
- 30
- Location
- Wales
How long do I run engine for to see if it pops out
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
Just spin it over. But use extreme caution, the thing may come out like a bullet, and there will be diesel spraying around all over the place.
Tomjones12
Member
- Posts
- 30
- Location
- Wales
Engine running but no movement
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
Not surprised. It isn't really a recommended technique, which is why I didn't recommend it.
Tomjones12
Member
- Posts
- 30
- Location
- Wales
I definitely don't want to remove head its due to.go.for not tomorrow
Tomjones12
Member
- Posts
- 30
- Location
- Wales
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
Try and pull it out with a screw, then.
But I suspect you will have to cancel the MOT anyway, unless you have a good spare injector in stock.
Tomjones12
Member
- Posts
- 30
- Location
- Wales
I
Have a new injector to replace it
Tomjones12
Member
- Posts
- 30
- Location
- Wales
Did try n get a dill at it but no good as not enough room.
Think the running it might not work as there is only the compression working for you, not a charge of diesel firing as well.
Probably also won't help that the engine is cold.
Wonder if starting it up then using easystart might help.
(I've used the slacken the clamp bolt & start it on my Sprinter when an injector is well glued in with the 'Black Death' & always worked, but the injector is functioning so you get the added power of a charge).
Probably also won't help that the engine is cold.
Wonder if starting it up then using easystart might help.
(I've used the slacken the clamp bolt & start it on my Sprinter when an injector is well glued in with the 'Black Death' & always worked, but the injector is functioning so you get the added power of a charge).
Tomjones12
Member
- Posts
- 30
- Location
- Wales
Tomjones12
Member
- Posts
- 30
- Location
- Wales
Only the nozzle and end cap are stuck as the main body came out but when I tried screwing it back in the thread on end cap broke
Tomjones12
Member
- Posts
- 30
- Location
- Wales
Worth a try where shall I spray it into the turbo or undo the intercooler pipe from inlet manifold and spray it directly into it
