Heating diffusion problem

Via google traduction

Hello to you I am French but as our land rover forums are empty, I allow myself to come and post my problem here. thank you in advance

I just had a 2007 sport rover, and I have a heating problem.

On the right everything works, but left cons left air conditioning works but when I ask for hot I have nothing, I would say that the hottest temperature I can have is the outside temperature ....

I thought it was a problem heating resistance left side but it seems to me that there is one and therefore as I have heating right, it is certainly not her.

So after I think of the "mixer", but when I see the brothel to change it I prefer to ask for help before undertaking anything.

I said that when I touch the knob of heating (left or right), I hear a sound of valve that opens or closes ....

Can be a probe ....

I specify that my range is a French so flying left.

Thanks for reading me

We have a few frogs French here that are great guys.
Sounds like what we call ‘blend motors’

Welcome

RangeRoller dt said:

We have a few frogs French here that are great guys.

Click to expand...

Looks who's using his new found abilities

Thank you for this welcome dear english friends.

Regarding the "blend motor" when I go from cold to warm, I hear a motor or valve operated for 8 seconds, so the "blend motor" works, right?

All I can say is when my blend motor works it changes from hot/cold.
It jams now and again and although i can hear it it doesn’t change for while. Is different model.

Have you checked searchbar here?

Shimsteriom said:

Look, I accept full responsibility for his new found abilities

Click to expand...

Hi

just wondering if it may be worth doing a hevac reset

With the HEVAC try this to reset the actuators that control the heat:

With ignition off press and hold the ECON & RECIRC buttons whilst turning ignition on (no need to start car).

The control module will then compare the current HEVAC actuator motor positions with the values stored in the module and will indicate an error by flashing the ECON LED.

If there are no errors, the LED will go out and the system will function normally.

To confirm that there are no errors, turn the ignition switch to the OFF position, then back to the ON position.

Observe the operation of the programmed defrost LED.

If there are errors present, the programmed defrost LED will flash and the system will attempt to calibrate itself.

Hope this helps

No I did not check in the search bar of this forum. I'm going to watch tonight.

Gstart I'm going to look at this and I'm coming back to you. Thank you for your answers.

Thank you gstart and range roller

And Shim for teaching me French

Nico2121 said:

No I did not check in the search bar of this forum. I'm going to watch tonight.

Gstart I'm going to look at this and I'm coming back to you. Thank you for your answers.

Thank you gstart and range roller

Click to expand...

ur very welcome

also here is the part of the workshop manual, press download after opening the link and scroll down , it describes the entire heating / cooling system

https://onedrive.live.com/?authkey=!AMrvOm7c4l3jJkg&cid=4BC2D89C85C7C171&id=4BC2D89C85C7C171!26586&parId=4BC2D89C85C7C171!26574&o=OneUp

also , check ur cabin filter is clean

if no joy please let us know, it might need a diagnostic reader plugged in but let’s see what u find first

RangeRoller dt said:

And Shim for teaching me French

Click to expand...

that’s handy then , was wondering what the brothel translation in the first post was, lol

Shim translation
“ google has sent me to you fine gentlemen, I must warn thee I am French and have a RRS. Since all my nations Landy forums contain French people I must lower myself to ask here, as I bow before your mighty glory with thanks”

RangeRoller dt said:

Shim translation
“ google has sent me to you fine gentlemen, I must warn thee I am French and have a RRS. Since all my nations Landy forums contain French people I must lower myself to ask here, as I bow before your mighty glory with thanks”

Click to expand...

will just send the OP to the tower after, lol

@gstuart

I tried to manage hevac, I had no fault but rolling a little I realized that it worked.:RE

I drove 1 hour and everything went perfectly. I ate but leaving 1 hour later, it did not work, I redid the handling hevac but it still does not work .....: furious:

I looked at my filter and it is clean. I also looked at the manual which seems a little complicated. :Oops: Anyway, here's the good mood, that's nice.

You need to put “@“ in front, then click his bar as you start typing the name...

Par example..
@gstuart

[QUOTE = "RangeRoller dt, post: 4681645, member: 151122"] Vous devez mettre "@" devant, puis cliquer sur sa barre lorsque vous commencez à taper le nom ...

Par exemple ..
[USER = 46096] @gstuart [/ USER]
[/CITATION]

Tres bien

Nico2121 said:

gstuart
I tried handling hevac, I had no fault but rolling a little I realized that it worked.:RÉ
I drove 1 hour and everything aler perfectly.

I ate but coming out 1h after, it did not work, I redid hevac manipulation but it still does not work ..... :furieux:


I looked at my filter and it is clean. I also looked at the manual which seems a little complicated. :Oops:


In any case, here is a good mood, it's nice.

Click to expand...

thks, so it’s an intermittent fault, nothing is ever easy

so if I’m reading it right as urs is LHD it’s the drivers side that u don’t get any heat from

few more things to check

check ur water level

with it set on heating, close all the vents off on the right hand side so only the drivers side has open vents,

see if u get heat from any of the vents on the drivers side plse

let us know how u get on

Yes, it's left, driver side.

I have already closed all the right side to leave only the left sides open but it has not changed anything.

Try openin t’ window fir now

RangeRoller dt said:

Try openin t’ window fir now

Click to expand...

Now try opening the fire window ?

google does not understand and me neither