mud muppet
New Member
- Posts
- 964
- Location
- burton upon trent
disco 200tdi ,is it a sensor?:scratching_chin:
handbrake light comes on when cornoring.
- Thread starter mud muppet
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
mud muppet
New Member
- Posts
- 964
- Location
- burton upon trent
i did check the other day seemed to be up to mark.but will check again in morning.taa
Tim Roebuck
New Member
- Posts
- 6
Hi - New Member looking for some advice. My 90 1988 Petrol seems to lose power when accelerating in 3rd 4th then 5th maxing at 45 mph, can anybody relate or offer advice on what I can do to help improve its performance please?
Soloby Rob
Banned
- Posts
- 7,714
- Location
- In a house, not far from somewhere
Tim Roebuck
New Member
- Posts
- 6
Yep - already see that it seems to be bit of a club, happy to take crap from a few sad loney hearts - but general help / advice is great - but I'm sure you'll get the "nothin in life is free" crap from nurse evil!
Tronicus Maximus
New Member
- Posts
- 265
- Location
- Selby
yeh but don't give the right to hi-jack someone else's thread. ignorance is no excuse, read rules.
Back to original topic, sounds quiet bad, there shoudn't be any sensors on a 200tdi should there?
unless your handbrake cables got wrapped round part or the chassis or a bit of debris stick in the chassis? so when body rolls in corners, tugs on handbrake cable?
- Posts
- 7,332
- Location
- Under my landy
Don't hold onto the hand brake when going round corners too quickly???
But seriously... could be a slightly loose connection on the switch?
But seriously... could be a slightly loose connection on the switch?
- Posts
- 66,516
- Location
- The Wooly Witch
Could be one of the wires has 'rubbed' thru the insulation and is shorting to the bodywork or summat in the tunnel.
- Posts
- 14,902
- Location
- Doncaster
My handbrake lever 'stop' (bit of plate welded on the top of the lever) had snapped on one side and bent, caused the lever to knock the switch into a different position which gave similar problems. I just bent it back and added a spot or three of weld to fix it. Easiest way to do it was to remove handbrake lever ... however, I dunno if the 200 handrake lever is the same as my 300 variant.
- Posts
- 66,516
- Location
- The Wooly Witch
Depends if your 300tDi is attached to a R380 box as I think the cable connections are different.
RHD handbrake lever ANR3692 is for the 300 I think, James will confirm or otherwise.
- Posts
- 14,902
- Location
- Doncaster
Depends if your 300tDi is attached to a R380 box as I think the cable connections are different.
RHD handbrake lever ANR3692 is for the 300 I think, James will confirm or otherwise.
It does have the R380 ..
douglasfaulkner
New Member
- Posts
- 26
If the handbrake light comes on when you apply it normally
I would think there is a short circuit to the chassis somewhere
if it doesn't come on normally then the plug in the back of the
switch is moving around a bit and not actually plugged in.
I would think there is a short circuit to the chassis somewhere
if it doesn't come on normally then the plug in the back of the
switch is moving around a bit and not actually plugged in.
- Posts
- 66,516
- Location
- The Wooly Witch
NTC 6125 handbrake cable
Eng.
DISCOVERY 1All1993 - 1993KA055569 >DISCOVERY 1All1994 - 1994RANGE ROVER CLASSICAll1989 - 1992RANGE ROVER CLASSICAll1993 - 1993> KA628986
NTC9400
DISCOVERY 1All1989 - 1992DISCOVERY 1All1993 - 1993> KA055568RANGE ROVER CLASSICAll1987 - 1988
NTC 5088
DEFENDER (NOT NAS)All1987 - 199390 Only RHDDEFENDER (NOT NAS)All1994 - 199490 Only RHD > LA935629
More info check here...
Quality Land Rover Parts Spares and Accessories Online
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
switch is in the same place ,levers between 200 and 300 are different thought look similar ,usually switch (but often shows up as light staying on with lever down)or low fluid or poor fluid level switch
mud muppet
New Member
- Posts
- 964
- Location
- burton upon trent
topped up the liqud stuff.see if that makes a diff.unfortunatly aint goin out in it till friday.
thanks for all advice.if still comes on will investigate the suggestions.:rolly:
thanks for all advice.if still comes on will investigate the suggestions.:rolly:
