P38A EAS Leaks - Help Needed

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Ok so know I'm even more confused. If I inflate the rear using the valves it doesn't go down overnight.
But when I removed the delay relay from under the passenger seat the rear went down but both fronts stayed up.
I will post a screen grab later showing the retrieved height sensor info from the EAS suite.
 
No I just fitted the schrader valves to the rear airbags. Inflated them manually and left them overnight and they didn't deflate. I never actually started/ran the car like this.

Unfortunately no nanocom ;(

I am looking to sell the car soon so need to get this sorted before I do.
 
PastyMuncher83 said:
Ok so know I'm even more confused. If I inflate the rear using the valves it doesn't go down overnight.
But when I removed the delay relay from under the passenger seat the rear went down but both fronts stayed up.
I will post a screen grab later showing the retrieved height sensor info from the EAS suite.
Click to expand...

Leaking rear valves in the valve block. Or the rear pipe connectors in the valve block
 
I bought a brand new valve block and fitted it before I first fired up the eas after converting from coils. Last week I swapped it out for the original valve block that was already fitted to the car just to see if it made a difference and same thing happened as before.

If I install new height sensors is it possible to calibrate them using the EAS Suite from the existing height setting figures I've already extracted from using EAS suite?

Thanks for all the input
 
PastyMuncher83 said:
I bought a brand new valve block and fitted it before I first fired up the eas after converting from coils. Last week I swapped it out for the original valve block that was already fitted to the car just to see if it made a difference and same thing happened as before.

If I install new height sensors is it possible to calibrate them using the EAS Suite from the existing height setting figures I've already extracted from using EAS suite?

Thanks for all the input
Click to expand...
EAS Suite will recalibrate...but the bit counts of each individual sensor will vary as they are not precision devices....they'll be there or there abouts, but not the same!
 
Ok will do, I got my new compressor and block from Kurt.

I will do some research I'm getting fed up with chucking parts at it in the hope the problem goes away!
 
Just found out a good trick to disable the self levelling when the ignitions off. Apparently if you got a standard 4 pin relay in place of the delay timer the EAS won't run with the ignition off.
Going to try it with a yellow one from the fuse box.
It says to keep the 6 pin standard relay in the car as you need t for diagnostics but hopefully this might solve my issue!
 
Well I will know for sure in the morning but fitting a 4 point relay (yellow from the engine bay fuse box) seems to have solved the issue!! Am in north Devon on holiday this week so longest I've left the car is 3 hours, and that was in high mode and didn't drop at all. I live in hope!

These are the links I read about the relay mod-

http://www.rangerovers.net/forum/7-...on.html#/forumsite/20563/topics/223826?page=1

http://www.rangerovers.net/forum/7-...ay.html#/forumsite/20563/topics/157785?page=1
 
Ahhh....so you leave the relay in full time....got it....

pulling the original relay will do the same thing while the vehicle is off...it prevents the system waking to self level....

But you have to put it back again before you start the car....this other relay mod, prevents the self levelling while off, but also means you don't have to refit the original before starting again!
 
Saint.V8 said:
Ahhh....so you leave the relay in full time....got it....

pulling the original relay will do the same thing while the vehicle is off...it prevents the system waking to self level....

But you have to put it back again before you start the car....this other relay mod, prevents the self levelling while off, but also means you don't have to refit the original before starting again!
Click to expand...

Yes Ant the four pin relay will just switch ECU on with ignition. As the two timer pins are missing the relay cannot wake the ECU up to self level. If the timer relay is playing up i suggest it is stripped and checked for dry or incomplete joins.
 
Last edited:
Yes sorry should of been clearer yes you leave the 4-pin in there.

I'm more than happy to leave it as it is don't need the self levelling when the things parked! I just hope it's not sat on its arse come sunrise ;) Thanks for all the advice either way.
 
You must log in or register to reply here.

Similar threads

B
P38A EAS compressor running almost continuously
Replies
7
Views
2K
Mark Piercy
Mark Piercy
oakey
L322 EAS Valve block
Replies
6
Views
597
oakey
oakey
IandiscoV8
P38A EAS Fault finding threads or files.
2 3
Replies
55
Views
4K
Mark Piercy
Mark Piercy
rangie1998
P38A EAS some more questions!
Replies
16
Views
1K
rangie1998
rangie1998
300bhp/ton
P38A Odd EAS behaviour - sinking front
Replies
19
Views
1K
Mark Piercy
Mark Piercy
Back
Top