can any of you guys tell me how long it should take to change the height from normal to off road height ? and how long it should take to drop from normal to access height? and then from access height to normal? ive had loads of eas problems but seem to be getting to the bottom of them but everything seems a bit slow, but i dont know how quick it should should function as its never worked properly.
eas hieght change durations?
- Thread starter paulvasey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
Mine changes up or down within 3 seconds
Pretty quick once I changed my air compressor
Pretty quick once I changed my air compressor
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
Yep
Completes the whole change in height within a few seconds
Yours sounds like its taking way too long
Does it take 30 seconds even when going down from off road height to normal height ??
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
Oh so not the pump them
EAS could probably do with being re-calibrated
Mine worked quicker after calibrating it
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
Yep you could be right there
If you go to a local independent land rover specialist it shouldn't cost more than £60
Or you could buy an all comms and do it yourself
Failing that someone nearby with an all comms may be able to help
Post your location someone may help you out for a few beer tokens lol
- Posts
- 16,482
Mine takes about 20 seconds to fully settle from standard to high - main change is done in about 5 seconds, but then the final 15 or so its taken up with monor corrections...
I have new Bags fitted all round (Oct 2011), not sure on compressor, might take a gander at it.
Access to standard is about 5 seconds....
I have new Bags fitted all round (Oct 2011), not sure on compressor, might take a gander at it.
Access to standard is about 5 seconds....
Datatek
Well-Known Member
- Posts
- 46,081
- Location
- Near Poitiers SW France
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
- Posts
- 16,482
Changed before I bought the car - didn't hurt a bit!!
- Posts
- 16,482
Yep - LR Dealer did it before I got the All Comms....yours seems to take its time too lol
guessing you have re-calibrated
Always surprised me how slow it changes - never had any change issues, just a tad slow - might check the Compressor for out put!!
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
Wheel diameter should make no difference
when calibrating you have to specify wheel size.
otherwise the car will sit too high or too low.
when i put 20" on mine, it was sitting high. so recalibrated and changed the wheel size from 19" to 20" and it was much better after.
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
- Posts
- 16,482
L322 Calibration measurements are taken from the bottom of the Wheel Rim not the centre of the wheel rim like the P38...Wheel diameter should make no difference
So a different Rim Dia. will effect the ride height measurement!
- Posts
- 16,482
Could be - fingers crossed it can wait till the new year...yep compressor could be on its way out
After the fuel pump, I need to change the Rad next (Pin hole caused by a stone chip by the looks of it) uses about a pint every 10 days....
The fuel pump money was what I was gonna use to change the rad...so that is delayed by a month!!
