- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
Feckin' arse. Paid for all the bl**dy alignment to be done last month.
Right, booked in for Monday. Arse, arse and bl**dy arse.
P38A Drag link disaster
- Thread starter Grrrrrr
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Feckin' arse. Paid for all the bl**dy alignment to be done last month.
Right, booked in for Monday. Arse, arse and bl**dy arse.
- Posts
- 16,475
Drag link doesn't alter tracking - the track rod that ties the two hubs together does...the drag link will alter steering wheel centre and subsequently steering box centre.
- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
Thanks, Saint. Steering is slap bang in the centre and she doesn't wander off anywhere so reckon I am good then.
Rangie Disco Sportsman
Active Member
- Posts
- 114
- Location
- Somerset
Check the alignment of the pitman arm a lot of places will do the tracking by altering the tie rod which puts the steering wheel off centre - they then correct this by altering the drag link length which leaves the pitman arm in the incorrect position at straight ahead - there are marks on the steering box to line up.
Another thing to consider is the lower steering shaft.
Another thing to consider is the lower steering shaft.
- Posts
- 58,170
- Location
- Preston Lancs.
It's amazing the number of people on here that don't have a bloody clue what they are talking about. 
- Posts
- 58,170
- Location
- Preston Lancs.
Slight up and down movement of a TRE is acceptable as long as there is no lateral play.
It's amazing the number of people on here that don't have a bloody clue what they are talking about.
That’s what you’re here for
but we can’t just call it Wanmerszone can we.
- Posts
- 16,475
Who? Me?It's amazing the number of people on here that don't have a bloody clue what they are talking about.
- Posts
- 58,170
- Location
- Preston Lancs.
- Posts
- 2,427
- Location
- Isle Sheppy
I'm in Preston Monday delivering cars wish I was delivering mine to wammers get it running right
- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
Thanks, Wammers. I'll try and have a look when it stops raining. Had a bit of another disaster today and didn't do much than fix that ...
Rangie Disco Sportsman
Active Member
- Posts
- 114
- Location
- Somerset
Can't recall entirely but seems to think when I had issues a couple of time with juddering that were due to alignment the passenger armrest wobbled side to side. I don't think there was any juddering through the steering wheel.
- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
Ordered anti-roll bar links. They're not expensive and mine are rusted to hell. About the only thing I've not replaced so might as well make it a full set!
- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
Drag link assembly replaced and still doing it. Not quite as bad but same speed. Now beginning to think there is a bit of play in the off-side track rod end. I think the roads are just mullering any ball-joint, 4x4 or other.
Antirollbar links arrive tomorrow (hopefully) so might get a chance to swap them out. Failing that, TRE.
Antirollbar links arrive tomorrow (hopefully) so might get a chance to swap them out. Failing that, TRE.
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
You're getting some experience on the drag links. ..
.... guess that makes you the forum drag queen
.... guess that makes you the forum drag queen
- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
Finally got around to fitting them as I have been away on holiday. No difference.
- Posts
- 18,954
- Location
- Buckinghamshire, UK. ('95 DT)
It is better but I still have a little wobble at a certain speed.
@wammers: replaced the whole drag link assembly: improved slightly. Wheels rebalanced: improved slightly. Anti-rollbar links replaced: no difference. There is ever so slight up/down in the offside balljoint on the track-rod. We're talking fractions of a millimetre but enough to move and click whereas the nearside has no movement at all. Can you get that ball-joint on its own off Lemforder? All I can see if the full track rod assembly? Any other ideas?
- Posts
- 58,170
- Location
- Preston Lancs.
TRE is QFS000010. But don't go to Rimmers for it unless you have a good mortgage supplier. Loads on Ebay. Island etc.
Datatek
Well-Known Member
- Posts
- 43,918
- Location
- Near Poitiers SW France
Not worth replacing just one end of the track rod IMO as if one is worn the other will not be far behind it and when the fixed one fails, the new track rod will come with both ends.
Any movement in the joints and it's fecked.
