- Posts
- 58,170
- Location
- Preston Lancs.
Plus the fact that they are not Beru plugs but Quintin Hazel pattern ones. Equivelent to Beru 0100226229. They don't have the reduced tip and don't look right to me.
Last edited:
diesel, sometimes, wont start (when cold)
- Thread starter rfsimoes
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Plus the fact that they are not Beru plugs but Quintin Hazel pattern ones. Equivelent to Beru 0100226229. They don't have the reduced tip and don't look right to me.
- Posts
- 58,170
- Location
- Preston Lancs.
It will if the lift pump stops working under normal conditions. Not if fuel lines and injection pump are empty.
rfsimoes
Member
- Posts
- 65
- Location
- S. Domingos de Rana, Lisbon,Portugal
Either the code QGP151 OR BERU 0100226229 checked equivalent for this engine.
QGP 151,QUINTON HAZELL QGP151 Glow Plug for BMW,ALFA ROMEO,MERCEDES-BENZ,OPEL,FORD
Am I wrong? AGAIN?
Datatek
Well-Known Member
- Posts
- 45,809
- Location
- Near Poitiers SW France
Yes, that looks like a cheapo copy again, experience shows they do not work well.Either the code QGP151 OR BERU 0100226229 checked equivalent for this engine.
QGP 151,QUINTON HAZELL QGP151 Glow Plug for BMW,ALFA ROMEO,MERCEDES-BENZ,OPEL,FORD
Am I wrong? AGAIN?
This engine needs the correct glowplug of OEM quality or you will be flogging a dead horse.
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
rfsimoes
Member
- Posts
- 65
- Location
- S. Domingos de Rana, Lisbon,Portugal
What will be a good glow plug then?
Thor1950
Well-Known Member
- Posts
- 39,238
- Location
- Land of the midnight sun
ones that work
rfsimoes
Member
- Posts
- 65
- Location
- S. Domingos de Rana, Lisbon,Portugal
Well "work" goes from "just work" to "work very well".
Like the assumption I did about the glow plugs either work or don't. I't seems that it isn't always that way. They can be somewhere in between.
Datatek
Well-Known Member
- Posts
- 45,809
- Location
- Near Poitiers SW France
BERU, NGK, Delphi or Bosch for the BMW M51 engine.
rfsimoes
Member
- Posts
- 65
- Location
- S. Domingos de Rana, Lisbon,Portugal
Now, leaving work, only 2 times on the glow plugs and it started right off, without hesitation like the problem never happened.
Bad fuel? I use the same fuel from the same petrol station for along time now without any problems.
They say at the balcony that it is additivated diesel and cheaper than regular:jaw:.
The company site has a product "datasheet" that explains it is a 7% biodiesel 93% Diesel and some marketing addictive. Strange thing is that every value of the charts between regular diesel and this "special" one, is exactly the same.
I have filled the tank with regular diesel and had about 14 liter = 3.0795682 Imperial gallons.
I had negative "ground" problem. All the crimped terminals were isolated from the cable. I sorted all that out and problems went away. The head can't be isolated from the block can it? All that head bolts...
I'm glad is weekend
Bad fuel? I use the same fuel from the same petrol station for along time now without any problems.
They say at the balcony that it is additivated diesel and cheaper than regular:jaw:.
The company site has a product "datasheet" that explains it is a 7% biodiesel 93% Diesel and some marketing addictive. Strange thing is that every value of the charts between regular diesel and this "special" one, is exactly the same.
I have filled the tank with regular diesel and had about 14 liter = 3.0795682 Imperial gallons.
I had negative "ground" problem. All the crimped terminals were isolated from the cable. I sorted all that out and problems went away. The head can't be isolated from the block can it? All that head bolts...
I'm glad is weekend
Datatek
Well-Known Member
- Posts
- 45,809
- Location
- Near Poitiers SW France
Now, leaving work, only 2 times on the glow plugs and it started right off, without hesitation like the problem never happened.
Bad fuel? I use the same fuel from the same petrol station for along time now without any problems.
They say at the balcony that it is additivated diesel and cheaper than regular:jaw:.
The company site has a product "datasheet" that explains it is a 7% biodiesel 93% Diesel and some marketing addictive. Strange thing is that every value of the charts between regular diesel and this "special" one, is exactly the same.
I have filled the tank with regular diesel and had about 14 liter = 3.0795682 Imperial gallons.
I had negative "ground" problem. All the crimped terminals were isolated from the cable. I sorted all that out and problems went away. The head can't be isolated from the block can it? All that head bolts...
I'm glad is weekend
Personally I would not use any odd fuel mix like that unless I made it myself.
A good set of OEM quality glow plugs will set you back about £40.
rfsimoes
Member
- Posts
- 65
- Location
- S. Domingos de Rana, Lisbon,Portugal
Hi everyone,
The problem seem to be gone again, without any intervention besides a full tank of diesel.
3 cold starts with normal start behaviour.
The problem seem to be gone again, without any intervention besides a full tank of diesel.
3 cold starts with normal start behaviour.
- Posts
- 58,170
- Location
- Preston Lancs.
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
Read this seem to be in conjunction with your problem if you have changed your glow plugs then I would be look here
- Posts
- 58,170
- Location
- Preston Lancs.
Read this seem to be in conjunction with your problem if you have changed your glow plugs then I would be look here
In other words the ECU temp sensor.
Grit Valve
2000 4.6 Vouge
- Posts
- 12,465
- Location
- Plaistow
In other words the ECU temp sensor.
Well there is two i think they both work in conjunction but the coolent is for cold start and fuel temp whist running in conjunction with water temp
- Posts
- 58,170
- Location
- Preston Lancs.
Well there is two i think they both work in conjunction but the coolent is for cold start and fuel temp whist running in conjunction with water temp
ECU coolant temp/fuel temp sensor for cold start. Gauge temp sensor has nothing to do with starting or running just for gauge.
rfsimoes
Member
- Posts
- 65
- Location
- S. Domingos de Rana, Lisbon,Portugal
Well there is two i think they both work in conjunction but the coolent is for cold start and fuel temp whist running in conjunction with water temp
I need to confirm this but I think one coolant temp sensor goes to to ECM and the other goes to Becm.
This is interesting because I built a low coolant/high temperature alarm. I'ts been working as expected, for a year by now. It is a high impedance input device so it should not interfere with the reading.
Anyway, the one that I "tap" for engine coolant temp, is the one that goes to the Becm and the only use that I'm aware of is the dial gauge at the instrument binnacle.
By the way, the Landy has been starting like a charm! No problem.
- Posts
- 16,482
I think one is the ECU, one is for the Temp Gauge on the dash and if you have A/C the thrid is for the HEVAC system....(can't remember if the early models had it on the engine and later on the Heater pipe - or the other way round!)
rfsimoes
Member
- Posts
- 65
- Location
- S. Domingos de Rana, Lisbon,Portugal
The A/C on mine, (1996) has a sensor on the heater pipe.
