P38A BECM replace or not?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
D

DodyDisco

Member
Posts
38
Location
Chester
My other half has kindly bought herself another project for me to sort out. It's a 2001 4.6 Vogue and hasn't been on the road for about 18 months. I've managed to sort out the EAS, HEVAC and ABS/TC problems and it's now MOT'd and back on the road. The next few problems I can do as and when. I noticed that when driving the doors lock and unlock on there own so I isolated the problem to the drivers side door lock and bought a replacement lock actuator. While I had the door card off and drivers door handle out I noticed the cam on the back of the drivers door handle had been drilled down the centre and a screw fitted so I need another door handle.

Now to the problem
It's at this point I started to consider getting a second hand BECM, door handle, barrel and speedo because I keep getting Fuse 2 RH/LH seat heater fuse blown and fuse 10 blown on the display when there's nothing wrong with the fuses plus the alarm and central locking has been disabled for some reason. The questions I have are.
What problems will it cause if I swap the BECM and associated bits for a second hand one?
Can I program my two used keys I have to work on the second hand BECM and just get replacement blades?

TIA. Pete
 
DodyDisco said:
My other half has kindly bought herself another project for me to sort out. It's a 2001 4.6 Vogue and hasn't been on the road for about 18 months. I've managed to sort out the EAS, HEVAC and ABS/TC problems and it's now MOT'd and back on the road. The next few problems I can do as and when. I noticed that when driving the doors lock and unlock on there own so I isolated the problem to the drivers side door lock and bought a replacement lock actuator. While I had the door card off and drivers door handle out I noticed the cam on the back of the drivers door handle had been drilled down the centre and a screw fitted so I need another door handle.

Now to the problem
It's at this point I started to consider getting a second hand BECM, door handle, barrel and speedo because I keep getting Fuse 2 RH/LH seat heater fuse blown and fuse 10 blown on the display when there's nothing wrong with the fuses plus the alarm and central locking has been disabled for some reason. The questions I have are.
What problems will it cause if I swap the BECM and associated bits for a second hand one?
Can I program my two used keys I have to work on the second hand BECM and just get replacement blades?

TIA. Pete
Click to expand...
Your existing BECM can be "Unlocked" and all settings read with the BECM, SM035 software, including the keyfob data. To replace the lock, you will need the set (Ignition barrel + transponder+ tailgate + drivers door) and of course at least one key.
The S/H BECM does not neccesarily, but it helps, if it does, come from the same donor car as the lockset. You need a "H" level BECM with a "YWC" part number, the higher the better.
Send the two BECM's off to "Rick the Pick" and he will "Clone" the spare from the original which means that the fobs will work.
You will of course have to get a spare blade cut unless you are lucky enough to get two fobs with the lockset (highly unlikely !!!) Then simply swap the blades to your existing fobs which is an easy job needing a small pin punch to remove the tiny spring pin...be careful you don't lose it !!
Good Luck
 
Dunno what it is John, taken in last Friday, chest pains, sickness and loss of appetite. They suspect it may be Gall Bladder related. She's having a scan today so I will know more later. Nice 80 mile round trip from here, good job I dont have the old 4.6, P38...I would be broke in a week and would have to hitch hike to your neck of the woods to get you to buy me some ale !!!
 
Irishrover said:
Your existing BECM can be "Unlocked" and all settings read with the BECM, SM035 software, including the keyfob data. To replace the lock, you will need the set (Ignition barrel + transponder+ tailgate + drivers door) and of course at least one key.
The S/H BECM does not neccesarily, but it helps, if it does, come from the same donor car as the lockset. You need a "H" level BECM with a "YWC" part number, the higher the better.
Send the two BECM's off to "Rick the Pick" and he will "Clone" the spare from the original which means that the fobs will work.
You will of course have to get a spare blade cut unless you are lucky enough to get two fobs with the lockset (highly unlikely !!!) Then simply swap the blades to your existing fobs which is an easy job needing a small pin punch to remove the tiny spring pin...be careful you don't lose it !!
Good Luck
Click to expand...
Thanks for the reply.

Do you know if I can get the data with a Nanocom? saying that i'm probably better letting someone who knows what they're doing lose on it
 
DodyDisco said:
Thanks for the reply.

Do you know if I can get the data with a Nanocom? saying that i'm probably better letting someone who knows what they're doing lose on it
Click to expand...
No you can't get that data with a nanocom,as Irishrover said,get in touch with Rick the pick in Brighton,he will sort it out for you,as long as you cross his palm,with silver.:D:D
 
DodyDisco said:
My other half has kindly bought herself another project for me to sort out. It's a 2001 4.6 Vogue and hasn't been on the road for about 18 months. I've managed to sort out the EAS, HEVAC and ABS/TC problems and it's now MOT'd and back on the road. The next few problems I can do as and when. I noticed that when driving the doors lock and unlock on there own so I isolated the problem to the drivers side door lock and bought a replacement lock actuator. While I had the door card off and drivers door handle out I noticed the cam on the back of the drivers door handle had been drilled down the centre and a screw fitted so I need another door handle.

Now to the problem
It's at this point I started to consider getting a second hand BECM, door handle, barrel and speedo because I keep getting Fuse 2 RH/LH seat heater fuse blown and fuse 10 blown on the display when there's nothing wrong with the fuses plus the alarm and central locking has been disabled for some reason. The questions I have are.
What problems will it cause if I swap the BECM and associated bits for a second hand one?
Can I program my two used keys I have to work on the second hand BECM and just get replacement blades?

TIA. Pete
Click to expand...

Have you checked the boot lock and button? Got a niggling memory that can cause door locks to do odd things.
 
You must log in or register to reply here.

Similar threads

jimmacD
P38 door handle repair.
Replies
0
Views
235
jimmacD
jimmacD
jimmacD
1999 P38 RF receiver is missing?
Replies
12
Views
872
Grrrrrr
Grrrrrr
feyniriel
P38 key not locking the car
Replies
10
Views
431
Rubberknees
Rubberknees
E
P38A Solved - Outer door handle not working
Replies
6
Views
946
EntropyUK
E
rangie1998
L322 Front doors deadlocked, do I have to break the locks?
Replies
1
Views
580
rangie1998
rangie1998
Back
Top