Anyone done a side exit on a puma?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
MoorlandBOB said:
if you modify a tdci will it work?also what are the insurance penalties for modded exhaust?...:confused:
Click to expand...

Have spoken with five tuning a few times on modding tdci's and they have done and had no problems usually a remap in conjunction to exhaust mods is preferable as to the insurence 'pass' :eek:
 
defo check before yam commit.

Also with the egg sauce, if it takes the same routing as a TD5 you can do what i did and take out all the boxes and get a rear section that exits under the rear wheel arch.

Side exits that exit in front of the wheel look ****.

Side exit tail pipe for Defender Td5 90
 
BIG_GINGA_BEARD said:
defo check before yam commit.

Also with the egg sauce, if it takes the same routing as a TD5 you can do what i did and take out all the boxes and get a rear section that exits under the rear wheel arch.

Side exits that exit in front of the wheel look ****.

Side exit tail pipe for Defender Td5 90
Click to expand...


yes i have a straight pipe from the centre box,it routs over the chassis between the rear tub body mount,it gives me the tyre clearance and also means i have a **** load less eggsauce lol..

i go take pics hang on...:p
 
Last edited:
;)ere poppy..like this is best for me.neat and tidy,no back box and above all tyre clearance...;)

i cut out the chequer plate out with a 2D water jet cut but that was free lol...

it can be done D.I Y with a hole saw...:)

i made the section of pipe from mid section OE to out rear tub with a disco 200 tdi down pipe that i cut on the bend and turned 180 degrees then re welded...

the bracket i made is a pipe clamp bodge that still works over a year later..I think ye whole lot cost me 40 quids..:D:D:D:D:D
 
Last edited:
MoorlandBOB said:
;)ere poppy..like this is best for me.neat and tidy,no back box and above all tyre clearance...;)

i cut out the chequer plate out with a 2D water jet cut but that was free lol...

it can be done D.I Y with a hole saw...:)

i made the section of pipe from mid section OE to out rear tub with a disco 200 tdi down pipe that i cut on the bend and turned 180 degrees then re welded...

the bracket i made is a pipe clamp bodge that still works over a year later..I think ye whole lot cost me 40 quids..:D:D:D:D:D
Click to expand...

Cool cheers gonna have to sit and work out route and have some natters with various tuning peeps :D
 
Forgottenpoppy said:
Cool cheers gonna have to sit and work out route and have some natters with various tuning peeps :D
Click to expand...
most said why you done that all you acheived is a few inches?...:rolleyes:

it meant i could replace the rear xmember and fit arch liners made from door mats to protect the rear chassis from damage.it also ment i had a 20 quid pipe section not way more for silencer etc.:D

you can be economic with rovers but it takes observation lol...;)

fuk the peps you pay use the local farm mechanic for notes.
 
Forgottenpoppy said:
Cool cheers gonna have to sit and work out route and have some natters with various tuning peeps :D
Click to expand...

I think it will be the lack of back pressure that will give you issues if you take all the baffles etc out. Only problem is that it will sound like a fart in a kazoo if you dont take it all out.
 
You must log in or register to reply here.

Similar threads

P
Transfer Box oil seals - are they the same on both sides of the case? - Puma 90 2.4
Replies
3
Views
595
Puma_Boy
P
D
3.9 V8 auto 14CUX limp mode/no power
Replies
3
Views
915
AllanWorms
AllanWorms
I
Not again .... headlights 62 plat puma 110
Replies
1
Views
538
iainmaoileoin
I
J
sound insulation
Replies
13
Views
851
JimNm
J
D
What loom would be best for my landrover 90 thats now running a 300tdi
Replies
14
Views
777
deccyb
D
Back
Top