Any one tried HTS 2000 aluminium repair stuff before?
- Thread starter Stretch
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Coffeelandy
Well-Known Member
- Posts
- 2,297
- Location
- SE Cornwall (forgotten part!)
QUOTE="Stretch, post: 3735106, member: 128695"]G'day Folks,
I was wondering if it is worth buying a few sticks and giving it a go =>
Any one here already tried the stuff?[/QUOTE]
Bloomin he'll that looks too good to be true! It's almost worth getting to just play with! I'll pass this link on to a blacksmith friend and see what he thinks.
I was wondering if it is worth buying a few sticks and giving it a go =>
Any one here already tried the stuff?[/QUOTE]
Bloomin he'll that looks too good to be true! It's almost worth getting to just play with! I'll pass this link on to a blacksmith friend and see what he thinks.
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,158
- Location
- Gloucestercotshirewolds
It gets pretty good reviews on the welding forums.
The main complaint is hardness difference compared to the Base metal so any stress cracks are likely to just pop up somewhere else and the far lower melting point means it has heat critical limitations.
I love the thread repair
The main complaint is hardness difference compared to the Base metal so any stress cracks are likely to just pop up somewhere else and the far lower melting point means it has heat critical limitations.
I love the thread repair
Yeah those videos always come across like washing powder adverts.
I think I might give it a go though. I've got to repair a lug on an aluminium gearbox casing and if there's anything left over I could see if it will glue a rip in a series wing back together
I think I might give it a go though. I've got to repair a lug on an aluminium gearbox casing and if there's anything left over I could see if it will glue a rip in a series wing back together
- Posts
- 58,170
- Location
- Preston Lancs.
Nothing new about that, used alloy brazing rod to assemble fabricated parts when i built my aircraft in the 80s.
payydg
Well-Known Member
- Posts
- 3,903
- Location
- Aberdeenshire
Not so expensive it's not worth a try. Drop a review on the forum once you've had a play.
I might try and repair my thermostat housing with it
I might try and repair my thermostat housing with it
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,158
- Location
- Gloucestercotshirewolds
Was it you that posted about a snapped bell housing lug? I was trying to remember after seeing this.
Some in house reviews would be good
bluedog333
Well-Known Member
- Posts
- 5,335
- Location
- Henley on Thames, Oxfordshire
Good find. Definitely worth getting some if it works.
I've just ordered some on flea bay - should be here in Holland by the end of the month!
If any one gets them before me, feel free to tell me if I need to get a refund or not...
...I'll do some pictures of the repairs I've got planned and see how I get on with them.
Some guys on the series 2 club forum are not so keen on this product - but others say they've done well - the main concern seems to be removal of the HTS alloy if you've put too much on.
If any one gets them before me, feel free to tell me if I need to get a refund or not...
...I'll do some pictures of the repairs I've got planned and see how I get on with them.
Some guys on the series 2 club forum are not so keen on this product - but others say they've done well - the main concern seems to be removal of the HTS alloy if you've put too much on.
DiscoPol
Well-Known Member
- Posts
- 6,376
- Location
- The Land of Po
Im watching this thread for an in house un biased opinion, it looks good stuff.
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,158
- Location
- Gloucestercotshirewolds
Worth a nose around on the welding forums.
1st hand users rate it pretty high though apparently it's difficult to use on non horizontal surfaces.
- Posts
- 58,170
- Location
- Preston Lancs.
It's alloy brazing rod with flux. The old stuff i used you had to use Borax paste as a flux. Piece being joined or repaired has to be immaculately clean.
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,158
- Location
- Gloucestercotshirewolds
Ffs I nearly got excited then....
Ah old military trick eh? Build 'em up - knock 'em down...
Similar threads
