Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Pikeys Heap
- Thread starter Pikey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 83,231
- Location
- Embasinga stocæ
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
have acquired a 1tonne chain hoist for the princely sum of feckall.. 
that along with the 2legged chainset I have means that I can now shift chassis around & turn it over etc rapidly and simply.
I've done a bit more Welding on it over the weekend. Bloody ran out of gas. SOds law it had to happen 1st day of easter weekend Made some angle iron out of 5mm plate and reinforced the springhanger with it, using the Stick welder to weld them up.
that along with the 2legged chainset I have means that I can now shift chassis around & turn it over etc rapidly and simply. I've done a bit more Welding on it over the weekend. Bloody ran out of gas. SOds law it had to happen 1st day of easter weekend
Made some angle iron out of 5mm plate and reinforced the springhanger with it, using the Stick welder to weld them up.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Updated costs so far
Total spend to date:
Trailer Hire Free
VAn Hire Free
Chassis £100
Fuel to collect Chassis £45
MacAllister 115mm Angle Grinder. £20
20 x 1mm cutting discs £12
rental for gas bottle & bottle refill £96
5Kg roll of welding wire £16 (£32 if you include the one BB got as well)
REplacement Salisbury axle diff pan £10
Replacement rear door £95
Total so far about £400
Total spend to date:
Trailer Hire Free
VAn Hire Free
Chassis £100
Fuel to collect Chassis £45
MacAllister 115mm Angle Grinder. £20
20 x 1mm cutting discs £12
rental for gas bottle & bottle refill £96
5Kg roll of welding wire £16 (£32 if you include the one BB got as well
)REplacement Salisbury axle diff pan £10
Replacement rear door £95
Total so far about £400
Last edited:
defender11069
AKA Mr cool...
- Posts
- 8,616
- Location
- up sh*t creek with out a paddle
Updated costs so far
Total spend to date:
Trailer Hire Free
VAn Hire Free
Chassis £100
Fuel to collect Chassis £45
MacAllister 115mm Angle Grinder. £20
20 x 1mm cutting discs £12
rental for gas bottle & bottle refill £96
5Kg roll of welding wire £16 (£32 if you include the one BB got as well
REplacement Salisbury axle diff pan £10
Replacement rear door £95
Total so far about £400
getting a fender back on the road....priceless..
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Got sent to the workshop to collect the tent for the weekend. So I thought I'd sneak an hr on the welder.. and welded the spring hanger back on. A bit OTT but to make sure it stays on, I'd previously made and welded an angle piece to each side, made out of 4mm steel.
That fooker int going nowhere.. Just need to weld the top where it joins the chassis.
That fooker int going nowhere.. Just need to weld the top where it joins the chassis.
Last edited:
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Did a bit more yesterday. Finally getting to the end of all the patching. This corrosion where the AFrame crossmember sits on the chassis is typical of Crap British design and engineering. Mud sits in the dip and rots the fecker out. So I'm doing a bit of a redesign.
Spring hanger back on.. ten times stronger than the original was.
Spring hanger back on.. ten times stronger than the original was.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Well all the patching and repairing is done,
All that's needed now is the rear crossmember from Pressbrake, then cut the rotten arse off and weld noo crossmember on. To make sure everything goes back where it's supposed to I've made a jig to line everything up.
Had a busy day today As I bought these this morning from a farm sale and auction.
All that's needed now is the rear crossmember from Pressbrake, then cut the rotten arse off and weld noo crossmember on. To make sure everything goes back where it's supposed to I've made a jig to line everything up.
Had a busy day today As I bought these this morning from a farm sale and auction.
- Posts
- 83,231
- Location
- Embasinga stocæ
looking good Pikey - want a challenge with Tufftee?
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
looking good Pikey - want a challenge with Tufftee?
I'm hoping not to take as long as you have with Tuffee
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Updated costs so far
Total spend to date:
Trailer Hire Free
VAn Hire Free
Chassis £100
Fuel to collect Chassis £45
MacAllister 115mm Angle Grinder. £20
20 x 1mm cutting discs £12
rental for gas bottle & bottle refill £96
5Kg roll of welding wire £16 (£32 if you include the one BB got as well )
REplacement Salisbury axle diff pan £10
Replacement rear door £95
pair of ex Military front doors £78.
Total so far about £478.
Total spend to date:
Trailer Hire Free
VAn Hire Free
Chassis £100
Fuel to collect Chassis £45
MacAllister 115mm Angle Grinder. £20
20 x 1mm cutting discs £12
rental for gas bottle & bottle refill £96
5Kg roll of welding wire £16 (£32 if you include the one BB got as well )
REplacement Salisbury axle diff pan £10
Replacement rear door £95
pair of ex Military front doors £78.
Total so far about £478.
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,213
- Location
- Gloucestercotshirewolds
Oh yeah....forgot to say earlier....
You left the gas on before lz11
Ya MUPPET!
You left the gas on before lz11
Ya MUPPET!
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
As I'm awaiting delivery of the noo HD rear crossmember. I thought I'd make a start on renovating the replacement Bulkhead I purchased several years ago & which has sat in the workshop doing feckall.
The pics of it are here, if you've not seen a bulkhead before???
Bulkhead Rebuild Photos by redhand010 | Photobucket
Oh and reason why half the pics include a steel rule, is because I need to know dimensions when I start patching it up..
Have cut several rot patches away, today. But you'll have to wait for them pics, because I forgot to take me fone with me today..
& which has sat in the workshop doing feckall.The pics of it are here, if you've not seen a bulkhead before???
Bulkhead Rebuild Photos by redhand010 | Photobucket
Oh and reason why half the pics include a steel rule, is because I need to know dimensions when I start patching it up..
Have cut several rot patches away, today. But you'll have to wait for them pics, because I forgot to take me fone with me today..
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Crossmember has arrived from Pressbrake.
Just waiting for the instruction manual to arrive So I can figure out where it all goes
Just waiting for the instruction manual to arrive So I can figure out where it all goes
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,213
- Location
- Gloucestercotshirewolds
Just a bit of welding to do then!
- Posts
- 10,639
- Location
- Oxfordshire
think it goes on the back
