Datatek
Well-Known Member
- Posts
- 45,866
- Location
- Near Poitiers SW France
I also run 28 all round on 18" Goodyear Wranglers when running unloaded, it improved directional stability considerably. I up the rears to 34 loaded, 38 is too high IMO.
tyre pressures
- Thread starter hobnob
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 58,170
- Location
- Preston Lancs.
I have a 3" screw in the N/S front it keeps going down. What can be the problem. Do you think the valve could be leaking? 
Datatek
Well-Known Member
- Posts
- 45,866
- Location
- Near Poitiers SW France
Only a 3" screw? You need Willy Wonkers herbal penis enlargement creamI have a 3" screw in the N/S front it keeps going down. What can be the problem. Do you think the valve could be leaking?
That's the same thing. You never made the mistake of stepping foot in PC World? I went in to get a new WiFi PCI Adapter for a machine, their sales staff then tried to convince me that buying a new PC was a cheaper option and I was wrong for thinking I could just simply replace the failed component. Although if I brought in my PC they could install the card because "if you get it wrong, you could kill yourself."Seems you have failed to grasp the difference between "PC World" and "PC world" one is descriptive of a trade name, the other descriptive of a load of over self important, interfering, pompous arseholes.
Only difference between those at PC World and those at PC world is one group use mind map rather than brainstorm and the other still live in their parents basement. They are all self centred opinionated arse holes who stick their oar in everyone else business because in their mind they are right and everyone else in the world is wrong, but with their interference the world would be a better place.
- Posts
- 58,170
- Location
- Preston Lancs.
Yeah i have been there and done that, their advice is at times incredulous. After the first PC i bought for the kids to do school work on way back when, which was a total ripoff. I have always built and upgraded my own. I don't see any point in paying a £1000.00 or more for something you can build for £300.00. Long live the free thinkers.
I was never daft enough to buy a machine from them, I only went there because I needed a new card quickly and I knew that'd have them. When you look at the prices you do wonder who'd be naive enough to buy a machine from somewhere like that.Yeah i have been there and done that, their advice is at times incredulous. After the first PC i bought for the kids to do school work on way back when, which was a total ripoff. I have always built and upgraded my own. I don't see any point in paying a £1000.00 or more for something you can build for £300.00. Long live the free thinkers.
- Posts
- 58,170
- Location
- Preston Lancs.
Only a 3" screw? You need Willy Wonkers herbal penis enlargement cream
Keith it's true. Spent most of last week playing with car. Removed dash. Took heater box out stripped it and re greased all the flaps. What was sticking was the quadrant that moves the distribution flaps. Very tight on it's pivot. Replaced all the degraded foam in matrix and dash to heater face. Which had been left misplaced by the previous prick who removed it and left screws and bolts out or loose everywhere. Did the blend motors, three new ones. Veleo "Made in China". Matrix O'rings. Re foam stripped all the vents and ducts. Heater works properly now for the first time since i bought it. Changed the aircon condenser. Boy was that knackered. All back together so nipped round block to post a letter came back and after about a twenty minute brew and relax. Went back out to car and N/S/F as flat as a bloody pancake. I can't recall running over half a dozen black cats on the way to the post box but must have done. New injection pump next week. So i am a busy lad
Last edited:
- Posts
- 58,170
- Location
- Preston Lancs.
I was never daft enough to buy a machine from them, I only went there because I needed a new card quickly and I knew that'd have them. When you look at the prices you do wonder who'd be naive enough to buy a machine from somewhere like that.
I got my first one from Comet i think for the kids mainly. In those days i knew as much about computers as i know about nuclear fusion.
Datatek
Well-Known Member
- Posts
- 45,866
- Location
- Near Poitiers SW France
Keith it's true. Spent most of last week playing with car. Removed dash. Took heater box out stripped it and re greased all the flaps. What was sticking was the quadrant that moves the distribution flaps. Very tight on it's pivot. Replaced all the degraded foam in matrix and dash to heater face. Which had been left misplaced by the previous prick who removed it and left screws and bolts out or loose everywhere. Did the blend motors, three new ones. Veleo "Made in China". Matrix O'rings. Re foam stripped all the vents and ducts. Heater works properly now for the first time since i bought it. Changed the aircon condenser. Boy was that knackered. All back together so nipped round block to post a letter came back and after about a twenty minute brew and relax. Went back out to car and N/S/F as flat as a bloody pancake. I can't recall running over half a dozen black cats on the way to the post box but must have done. New injection pump next week. So i am a busy lad
Done quite a bit of that on mine, not the FIP or the blends yet though.
Hard luck with the screw, last time i got one it was in a brand new tyre on the way home.:mad2:
