Search results

i know its a land rover thing but sometimes when you think its nearly done, well this morning got up first thing got stuck in made a bumper its ready to go to blasters before galvo. thinking to myself just the front end to paint this week and new brake disks and hoses to fit and of for mot...

looking at getting some think like pda ipad ect to use memory map i don't know anything about them so any advice about what i need to get going much appreciated spotted this on flee bay will it work and if so what else would i need 7inch Tablet PC Google Android,UK Seller.FreeDel.New on eBay...

on some site's that i use not land rover related if you buy swap or have any dealings with other members some have feed back section to rate members .have just swapped some bits with a member of this site.(Colin h.) top bloke cheers Colin and got me thinking if it may be a good idea. just a thought

well sun was out today so finally got a chance to finish of the sliders i have knocked up ready to go to shot blaster and galvanising next week

just had a look under 90 due mot soon both bulk head support brackets looking dodgy anybody fitted these is how crap of a job to do cheers050 Lower door pillar feet offside

hi just had offer of a set of van sides from a td5 i asume they are direct swop any one know are they the same (ie holes mounting points ect)as early defender cheers cheers

just testing the water here have 90 wich was 2.5 petrol have coverted it to 200 tdi used all the bits from my old disco .goes well no probs. problem is i have had offer from my mate v8 from his old sd1 all nice bits big valve heads ect, now what do i need to get it in my 90 can i use origanal...

anybody fitted plastic outer wing panels ones from mags about 65 quid. if so any good do they fit ok need new outer for my 90 caved old one in . but plastic just sounds wrong

cooper discovery stt 265,s will they be ok with standard width arches what they like for rubbing on inside anyone know cheers

was at a local retail park today spotted a defender with a really odd look about it. it had disco steel wheels on the front. and modulars on the back.but it was the difference in tyre sizes had me puzzled when i looked had 205 70 16 on front wheels and 235 85 16 on rear .i didn't think you could...

after converting my petrol 90 to tdi from my rotten disco just got round to fitting transfer box. after fitting and driving for a couple of days noticed bad oil leek on ground defo from transfer box as its gear oil not atf. so put it down to me catching input oil seal when fitting box took it...

does anyone know if diff ratios will be the same want to fit mark one disco rear axle into 87 defender.as its pi@@ing oil changed seal and still the same and have nice dry disco one plus will have four wheel disk brakes

anybody used plastic outer wing panel any good or crap both sides of my 90 are getting close to wanting replaced . don't know it just sounds wrong

hi does anyone know if series 3 doors are a easy swap for early defender lift up handle type ones

just completed converting 2.5 pet to 200 tdi very pleased pulls like a train when running the temp shows in the red on the gauge was told it would and to swap with petrol sender. problem is tdi one is fine pitch thread. pet one course pitch thread so is there a one i can use to sort out or does...

went out to do some work on the 90 yesterday and its decided to start leeking fuel from the tank its an 86 so early tank with one hole for sender unit does anyone know if later ones with two holes in top fit cheers

anyone got any idear about mpg i have just put disco 200 tdi into petrol 90 used 2.5 petrol box that was in the 90 and disco transfer box .tyres are 205 80 16 cheers

got a 2.5 petrol 90 last warning light on dash is marked 24 volt wats it for

have got a 200 tdi disco to brake to go into 2.25 petrol 90 is the petrol gear box ok to use .same gearing .wat changes will i need to make bell housing back plate ect ect and is it best to use disco transfer box

going to start striping my rust bucket 200 tdi disco this week. have got a petrol 90 to convert . so anythig i need to keep apart from engine back axel transfer box . bits that will come in useful as spairs in future for the 90. come on help needed