Search results

Anyone know the part No of the bolt that holds the Hummel thingie on the rocker cover:D Cant find it anywhere :mad:

Morning all Dont flame me until you read this:D Has anyone replaced the boot floor with ali checker plate and riveted it in Had a look at previous posts/did search but they all say weld in a new one:eek: Cheers Paul

For those who like to monitor their battery :D Electric Bike & Scooter Battery & Amp Hour Meter: Watt's Up

Just a thought-I know you change the oil every 6k miles but if you offroad a lot there will be lots of engine and not so much moving:D Any one know how many hours of operation between changes and anyone ever fitted an engine running hour meter:rolleyes:

Hi all Did a search but all a bit vague.Heater fan slide switch is intermittant.How do you remove it:confused: Front cover is easy but how do you get the swith out:doh: Cheers Paul

Just in case anyone needs to get them ;) Land Rover parts - FUEL SEDIMENTOR - DIESEL

Morning all i have changed all the calipers + the back disks and have ( I think ) got all the air out :D Peddle still seems a bit soft bur servo seems OK so I will replace the master cylinder:rolleyes: Will I have to bleed the entire system again:eek: as its a right PITA Cheers Paul PS anyone...

Anyone know the part No of the seal on the 300tdi outer timing belt cover where the crankshaft goes through-cant find it anywhere:rolleyes: and am about to pull it apart:D

Really silly question but the manual and threads just say to position the arm on the pump correctly on the cam :rolleyes: Does the arm go under or over the cam:confused:

Hi all I decatted a while ago and used a flexi front pipe I removed the rubber hanger that connected near to the cat as I thought it wasnt needed but have read somewhere that it is needed for the flexi :eek: The new front pipe didnt have an attachment for the hanger anyway :doh: Should I fit it...

Morning all I have fitted new pads to above and noticed the pads are a little taller than the discs:eek: Have fitted new front brake callipers now and the pads look thesame:doh:Will be changing rear discs and callipers at the week end:D Does this sound normal:rolleyes:

Hi all- when checking my acquired 1995 300tdi manual some time ago I noticed thet there were odd little bubbles around the no 4 injector:eek: I know the head had been skimmed and gasket changed so I replaced the injector washers as I had a set:D Thought this had solved the prob but noticed...

Hi all Can someone tell me the socket size needed to remove the rear brake disks (non ABS ) I think they are Bi Hex:rolleyes:

Daft question all-when you replace the thermostat is the jiggle thingy at 12 oclock or aligned with the small cut out on the housing at around 3 mins to 12:D

Another daft question I have bought some Hylomar sealant (the blue stuff) as I am going to change some gaskets on the engine and hubs etc -300tdi Can you use the same stuff on the water pump and P gaskets as well Cheers Paul:D

Hi all How much brake fluid does the system hold.ie how much to refill after a complete drain of the system:D

Hi all I cleaned out my sedimenter at the week end and to be honest it wasent too bad-just a bit of yellowy brown stuff. My advice is get two new seals if you do the job. When I seperated the two parts of the bowl that seal was really bad:eek: The seals only cost a few Euro and better safe than...

Morning all Can the rad and the intercooler be removed as separate units :) Rave and Haynes seem to show the whole lot comes out a a unit:eek: PS De catted and replaced whole exhaust system at the weekend:D

Morning all I have all the bits to decat and replace the whole exhaust. I can grind off the centre and tail pipes to fit the new but how do you remove the 3 bolts that attach the downpipe to manifold-the look hard to get at-any advice all:D

Hi all I was changing the gloplugs and found cylinder 3 gloplug is covered in engine oil when I take it out:eek: is this a prob Also anyone know the size of of the lock nut on the tappet adjuster as the last person to adjust stripped it As well as that the rocker cover gasket I got from...